Garmin GHP Reactor Hydraulic Manual de instrucciones de instalación - Página 6
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Equipamiento marino Garmin GHP Reactor Hydraulic. Garmin GHP Reactor Hydraulic 15 páginas.
Imprimir página
Corrosion Blocker
To ensure long life of all parts, apply corrosion blocker to the
pump at least twice yearly.
A marine-rated corrosion blocker should be applied to the pump
after all hydraulic and electrical connections are made and the
hydraulic system has been bled.
Connecting the CCU
1
Route the connector end of the CCU cable to the ECU and
make the connection.
2
Route the orange and blue wires from the bare-wire portion
of the CCU cable to the location where you plan to install the
alarm
(Installing the
Alarm).
If the cable is not long enough, extend the appropriate wires
2
with 0.08 mm
(28 AWG) wire.
3
Route the brown and black wires from the bare-wire portion
of the CCU cable to the location where you plan to install the
Shadow Drive
(Installing the Shadow
If the cable is not long enough, extend the appropriate wires
2
with 0.08 mm
(28 AWG) wire.
Installing the Shadow Drive
Connecting the Shadow Drive to the Hydraulic System
Before you can install the Shadow Drive, you must select a
location at which to connect the Shadow Drive to the hydraulic
steering of your boat
(Shadow Drive
For further assistance, consult the hydraulic-layout diagrams
included with your pump.
Use hydraulic connectors (not included) to install the Shadow
Drive in the appropriate hydraulic line.
Connecting the Shadow Drive to the CCU
1
Route the bare-wire end of the CCU cable to the Shadow
Drive.
If the cable is not long enough, extend the appropriate wires
with 28 AWG (0.08 mm²) wire.
2
Connect the cables, based on this table.
Shadow Drive Wire Color
Red (+)
Black (-)
3
Solder and cover all bare-wire connections.
Installing the Alarm
Before you can mount the alarm, you must select a mounting
location
(Alarm Mounting and Connection
1
Route the alarm cable to the bare-wire end of the CCU cable.
If the cable is not long enough, extend the appropriate wires
with 28 AWG (0.08 mm
2
Connect the cables, based on this table.
Alarm Wire Color
White (+)
Black (-)
3
Solder and cover all bare-wire connections.
4
Secure the alarm with cable ties or other mounting hardware
(not included).
NMEA 2000 and the Autopilot Components
If you have an existing NMEA 2000 network on your boat, it
should already be connected to power. Do not connect the
NMEA 2000 power cable to an existing NMEA 2000 network,
because only one power source should be connected to a
NMEA 2000 network.
6
NOTICE
Drive).
™
Mounting
Considerations).
CCU Cable Wire Color
Brown (+)
Black (-)
Considerations).
2
) wire.
CCU Cable Wire Color
Orange (+)
Blue (-)
NOTICE
You can connect the helm control and the CCU through an
existing NMEA 2000 network. If you do not have an existing
NMEA 2000 network on your boat, all the parts needed to build
one are supplied in the autopilot package
NMEA 2000 Network for the Autopilot
To use advanced features of the autopilot, optional NMEA 2000
devices, such as a GPS device, can be connected to the NMEA
2000 network.
If you are unfamiliar with NMEA 2000, you should read the
"NMEA 2000 Network Fundamentals" chapter of the Technical
Reference for NMEA 2000 Products. To download this
document, select Manuals on the product page for your device
at www.garmin.com.
Building a Basic NMEA 2000 Network for the Autopilot
System
If you are installing a NMEA 2000 power cable, you must
connect it to the boat ignition switch or through another in-line
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
1
Connect the three T-connectors
2
Connect the included NMEA 2000 power cable
12 Vdc power source
Connect the power cable to the ignition switch of the boat if
possible, or route it through an inline switch (not included).
NOTE: The braided drain wire (bare) on the NMEA 2000
power cable must be connected to the same ground as the
black wire on the NMEA 2000 power cable.
3
Connect the NMEA 2000 power cable to one of the T-
connectors.
4
Connect one of the included NMEA 2000 drop cables
one of the T-connectors and to the helm control
5
Connect the other included NMEA 2000 drop cable to the
other T-connector and to the CCU
6
Connect the male and female terminators
the combined T-connectors.
Connecting the Autopilot Components to an Existing NMEA
2000 Network
1
Determine where to connect the helm control
to your existing NMEA 2000 backbone
(Building a Basic
System).
NOTICE
together side-by-side.
to a 9 to
through a switch
.
.
.
to each end of
and the CCU
.
to