Garmin GPSMAP 5015 Manual de instrucciones de instalación - Página 9

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Equipamiento marino Garmin GPSMAP 5015. Garmin GPSMAP 5015 25 páginas. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
También para Garmin GPSMAP 5015: Manual de consulta rápida (2 páginas), Manual del usuario (2 páginas), Manual de consulta rápida (2 páginas), Información sobre seguridad y productos (48 páginas), Manual de instrucciones de instalación (25 páginas), Referencia técnica (42 páginas), Información sobre el producto (48 páginas), Declaración de conformidad (1 páginas), Plantilla de montaje empotrado (2 páginas), Manual complementario (24 páginas)

Garmin GPSMAP 5015 Manual de instrucciones de instalación
The GPSMAP 4000/5000 series chartplotter comes with a power cable, a NMEA 2000 drop cable, a 19-pin NMEA 0183 data cable, and a
17-pin Marine Video cable. Optional Garmin Marine Network components use specialized Garmin Network cables. Depending on the
installation, it may be necessary to drill holes to route the connector end of these cables.
Garmin rubber grommets are provided to cover these holes for a finished look.
You may not need the grommets in some installations. The grommets do NOT create a
waterproof seal. Apply a marine sealant around the grommet and cable after installation.
Be sure to test the system before installing and sealing the grommets. Purchase additional
grommets from your Garmin dealer or directly from Garmin at www.garmin.com.
Tools
Drill
1
1
/
in. (31.7 mm) paddle drill bit or hole saw
4
Utility knife
Marine sealant (optional)
To install the cable grommet:
1. Mark the location where you want to route the cable (power, NMEA 0183, NMEA
2000 Marine Video, or Marine Network.)
2. Using a 1
1
/
in. (31.7 mm) paddle drill bit or hole saw, drill the installation hole.
4
3. Refer to the diagram for trimming instructions. Carefully trim the cable hole in the
grommet, as needed.
4. Route the cable to the chartplotter, and test the system.
5. Spread the grommet apart at the split and place it around the cable.
6. Firmly push the grommet into the installation hole until it is seated. Apply marine
sealant, as needed, to weatherproof the cable.

Wiring the Power Cable

The GPSMAP 4000/5000 series chartplotter must be connected to the power supply for the boat. Use the 2-pin power cable included, and
connect the power (red) and ground (black) wires. Use 14 AWG shielded wiring for extended runs of wire to the power cable. Solder all
connections and seal them with heat-shrink tubing.
Wiring the GPS 17 Antenna
The GPS 17 antenna must be wired to the included 19-pin NMEA 0183 cable as well as to the power supply for the boat. Refer to the diagram
below when wiring the GPS 17 to the 19-pin NMEA 0183 cable. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183
cable or GPS 17 cable. Solder all connections and seal them with heat-shrink tubing.
NotE: If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS antenna.
The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network.
Garmin
GPSMAP 4000/5000
Series Unit
GPSMAP 4000/5000 Series Installation Instructions

Wiring and Cables

FUSe
7.5 A - 42 V
reD (POWer)
POWer
BlACk (GND)
CABle
OrANGe (ACC. ON)
NMeA 0183
GreeN (DATA OUT)
>
CABle
GreeN/WHITe (DATA IN)
>
Wiring the GPSMAP 4000/5000 Unit and the GPS 17
Trim to this line for
Trim to this line for
the Marine Video
the Marine Video
cable.
cable.
-
+
BATTery
WIre
10–35 Vdc
COlOr
reD (POWer)
BlACk (GND)
yellOW (ON)
BlUe (DATA IN)
WHITe (DATA OUT)
Use this hole (no
Use this hole (no
trim) for the power,
trim) for the power,
NMEA, Marine
NMEA, Marine
GPS 17 cable.
GPS 17 cable.
WIre
COlOr
FUSe
1 A
GPS 17
GPS/WAAS
>
Sensor
>
Network, or
Network, or
Split
Split