Brother P-touch H108 Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Etiquetadora Brother P-touch H108. Brother P-touch H108 2 páginas.
También para Brother P-touch H108: Manual del usuario (2 páginas)

Imprimir página

User's Guide

English

With your P-touch H107/H108, you can create labels for multiple

applications. Select from the many frames, character sizes and

styles to design beautiful custom labels. In addition, the variety of

tape cassette available allows you to print labels with different widths

and exciting colours.

Read this manual carefully before you begin and keep the manual in

a handy place for future reference.

Power Supply and Tape Cassette

Cassette

cover

Tape cutter

lever

Open the cassette cover by pressing the

above indicated area at the top end of the

P-touch.

If a tape cassette is already installed, remove it by

pulling it straight up. Also, if batteries are already

installed, remove them.

• Make sure that the power is turned off when

replacing batteries or tape cassettes.

LCD Display & Keyboard

Troubleshooting

 Error message

Message

Cause/Remedy

The batteries are weak.

If using AAA alkaline batteries: Replace them with new

Low Battery!

ones.

If using Ni-MH batteries: Charge them fully.

Battery Dead

The installed batteries have expired.

An invalid number was entered as the label length.

Invalid!

(This is not displayed in Auto Designs).

• You tried to print a text file when there is no data

stored in the memory.

•

is pressed when no text is entered.

No Text!

• You tried to select Text Preview or Cable Label when

no text is entered.

•

was pressed when no text was entered while

using the DECO MODE or Auto Designs.

• You tried to enter a 3rd line by pressing

Line Limit!

• You tried to print or preview two lines of text while

3.5mm or 6 mm tape is installed. Install tape of a

larger size.

You tried to print a label when there is no cassette

No Cassette!

installed.

The tape cutter lever was used during the printing

Cutter Error

process.

Safety Precautions

Indicates a potentially hazardous

WARNING

situation which, if not avoided,

could result in death or serious

injuries.

Follow these guidelines to avoid the risk of fire, burns, injury,

electric shocks, rupture, overheating, abnormal odours or

smoke.

• Do not touch the P-touch during a lightning storm.

• Do not use the P-touch in places of high humidity (such as bathrooms).

• Do not allow the P-touch batteries to get wet, for example, by handling them with

wet hands or spilling beverages onto them.

• Since loss of eyesight may result when leaked fluid from batteries gets into your

eyes, immediately rinse your eyes with a large amount of clean water, and then

seek medical attention.

• Do not disassemble or modify the P-touch batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the

batteries.

• Do not throw the batteries into fire or expose to heat.

• Remove batteries immediately and stop using the P-touch if you notice abnormal

odour, heat, discolouration, deformation or anything unusual while using or storing

it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

• Do not use a deformed or leaking battery or one with a damaged label. There is a

possibility of generating heat.

Ver. 02

Insert six new AAA alkaline batteries

(LR03) or fully charged Ni-MH batteries

(HR03), making sure that their poles

point in the correct directions.

Users of alkaline batteries:

Always replace all six batteries at the

same time with brand new ones.

Users of Ni-MH batteries:

Always replace all six batteries at the

same time with fully charged ones.

NOTE

Visit us at http://support.brother.com/ for the latest

information about the recommended batteries.

Size

14. Style key

Cursor

15. Character keys

Caps

16. Caps key

Underline/Frame

17. Symbol key

Width

18. Menu key

Style

19. Clear key

Label Length

20. Print key

If a specific label length has been

21. Enter key

selected,

also appears.

22. Auto Designs function key

Guidance (left, right)

23. Frame key

Power key

24. Accent key

10. Cursor key : Right

25. Space key

11. Cursor key : Left

12. Backspace key

13. Size key

NOTE

• The LCD shows one row of 12 characters; however, the text that

you enter can be up to 80 characters in length.

• While selecting the settings, press the Space key to go back to

the default item.

• The print preview is a generated image of the label, and may

differ from the actual label when printed.

• Label length shown on LCD may slightly differ from the actual

label length when printed.

Message

Cause/Remedy

The maximum number of characters (80 characters for

Text Full!

regular text, 50 characters for Auto Designs and DECO

MODE) have already been entered.

With the DECO MODE function:

Since the number of entered characters exceeds the

label length, reduce the text.

Text Limit!

All other functions:

Since the number of entered characters exceeds the

label length, reduce the text or select [Auto] as the label

length.

Printing on 3.5mm tape with invalid Frame setting ON.

No Frame OK?

(Select

to print with no Frame,

cancel).

Feeding tape after printing when [Chain Print] is

OK to Feed?

selected. Refer to "Setting Margin".

Only 12mm tapes are available for use with DECO

Insert 12mm

MODE function.

Wrong Tape!

Use a tape cassette with the

CAUTION

Follow these guidelines to avoid personal injury, liquid

leakage, burns or heat.

• When the P-touch is not being used, store it out of the reach of children. In addition,

do not allow children to put P-touch parts or labels in their mouths. If any object has

been swallowed, seek medical attention.

• Do not touch metal parts near the print head immediately after printing.

• Do not touch the cutter blade.

• If leaked fluid from batteries gets onto your skin or clothes, immediately rinse them

with clean water.

• Remove the batteries if you do not intend to use the P-touch.

• Do not use a battery other than that specified. Do not use combinations of old and

new batteries or combinations of different types, different charging levels, different

manufacturers or different models. Do not insert a battery with its plus and minus

ends reversed.

• Do not drop or hit the P-touch.

• Do not press on the LCD display.

• Do not put your finger inside the P-touch when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the

batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialized

battery charger before using the batteries.

General Precautions

• Depending on the location, material, and environmental conditions, the label may

unpeel or become irremovable, the colour of the label may change or be

transferred to other objects. Before applying the label, check the environmental

conditions and the material.

• Do not use the P-touch in any way or for any purpose not described in this guide.

Doing so may result in accidents or damage to the P-touch.

• Use only Brother TZe tapes with the P-touch. Do not use tapes that do not have

the

mark.

• Only use a soft, dry cloth to clean the P-touch; never use alcohol or other organic

solvents.

• Use a soft wipe to clean the print head; never touch the print head directly.

• Do not put any foreign objects into any part of the P-touch.

Print head

End of tape

Toothed

wheel

Tape guide

Insert a tape cassette, making sure that

it snaps into place.

• Make sure that the end of the tape feeds under

the tape guides.

• Use only Brother TZe tapes with P-touch.

Specifications

Dimensions:

Approx. 110(W) × 208(D) × 59(H)mm

(W x D x H)

Weight:

Approx. 390 g

(without batteries and tape cassette)

Power supply:

Six AAA alkaline batteries (LR03)

Six AAA Ni-MH batteries (HR03)*

Tape cassette:

Brother TZe tape (width)

3.5mm, 6mm, 9mm, 12mm

Visit us at http://support.brother.com/ for the latest information

about the recommended batteries.

 What to do when...

Problem

The display stays blank

• Check that the batteries are correctly

after you have turned on

inserted.

the P-touch.

• If the batteries are weak, replace them.

When the label is printed

• See "Setting Margin" in this users guide

out, the margin(space) is

and select [Half] or [Narrow] to have

too large on both sides of

smaller margins for your label.

the text.

• Check that the tape cassette has been

The P-touch does not

inserted correctly.

print, or the printed

• If the tape cassette is empty, replace it.

characters are not formed

• Check the cassette cover is properly

properly.

closed.

• If the batteries are weak, replace them.

• When power is disconnected for more

The setting has cleared

than three minutes, all text & formats in

on its own.

the display will be lost. Language and Unit

settings will also be cleared.

mark.

• There may be some dust on the print

head. Remove the tape cassette and use

A blank horizontal line

a dry cotton swab to gently wipe the print

appears through the

head with an up-and-down motion.

printed label.

• The print head can be cleaned more

easily if the optional print head cleaning

cassette (TZe-CL3) is used.

• Do not place the P-touch, batteries in direct sunlight or rain, near heaters or other

Indicates a potentially hazardous

appliances, or in any location exposed to extremely high or low temperatures (e.g.

situation which, if not avoided,

on the dashboard or in the back of your car). Avoid high humidity or dusty

may result in minor or moderate

locations.

injuries.

• Do not apply excessive pressure to the cutter lever.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and P-touch.

• Any data stored in memory will be lost due to failure or repair of the P-touch, or if

the battery expires.

• The P-touch is not equipped with a charging feature for rechargeable batteries.

• The length of the printed label may differ from the displayed label length.

• A protective clear plastic sticker is placed over the display during manufacturing

and shipping. This sticker should be removed prior to use.

• When power is disconnected for more than three minutes, all text, format settings

and any text files stored in the memory will be cleared.

Cutter's

edge

Tape

exit slot

Securely close the cassette cover, making

sure that it snaps into place.

Initial Settings

Start your P-touch.

Supply power by using six AAA batteries, and then press

Set the language.

[English/Español/Français/Hrvatski/Italiano/Magyar/

Nederlands/Norsk/Polski/Português/Portug. (BR)/

Română/Slovenski/Slovenský/Suomi/Svenska/Türkçe/

Čeština/Dansk/Deutsch]

Set the unit of measurement.

The default setting is [mm].

NOTE

• The P-touch automatically turns off if no keys are pressed within

five minutes.

• To cancel any operation, press

Problem

Solution

The P-touch has "locked

up" (i.e., nothing happens

when a key is pressed,

even though the P-touch

is on).

The power turns off when

you try to print.

The tape does not feed

properly or the tape gets

stuck inside the P-touch.

All text and format settings

need to be cleared to

create a new label.

The LCD is set to an

incorrect language.

[Language]

[Unit]

[inch/mm]

Solution

• Refer to "Resetting the P-touch".

• The batteries may be weak. Replace

them.

• Check that the batteries are correctly

inserted.

• If the batteries are weak, replace them.

• Check that the end of the tape feeds

under the tape guides.

• The cutter lever is used while printing. Do

not touch the cutter lever during printing.

• Press

and select [Text&Format].

• Refer to "Initial Settings".