Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi Procedimiento de instalación - Página 2

Navegue en línea o descargue pdf Procedimiento de instalación para Escáner Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi. Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi 5 páginas. Color duplex document scanner
También para Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi: Manual de procedimientos de instalación (7 páginas), Manual de procedimientos de instalación (9 páginas), Folleto (2 páginas), Folleto y especificaciones (2 páginas)

Fujitsu Fi-4750c - Color Duplex Document Scanner 50ppm 90ipm Ccd/scsi Procedimiento de instalación
M3093GX\DG\M3096G\GX\M3097G+\DG
Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI
Special note: The Fi-4340C shipping lock is a knob located underneath the exit tray. To unlock
it twist a quarter turn counter-clockwise so that it is vertical. The Fi-4530C does not have a
shipping lock.
Step C: Installing the SCSI Host Adapter.
1. Shut down your PC and remove the case cover.
2. Locate a free PCI slot and remove the back plate if necessary.
3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame
Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.
4. Boot your PC without the scanner attached
Step D: Installing the SCSI drivers (Adaptec).
1. When the New Hardware wizard comes up allow Windows to finish installing the files
for the SCSI controller.
2. Then go to www.adaptec.com, and click on the "search" tab. Scroll down to the
"Enter key word or quoted phrase" box and type in "aspi32.exe."
3. Next scroll down to the drivers section, click on "aspi32.exe" and follow the prompts
to download it to your desktop or a new folder.
4. Afterwards go to that location and double click on the "aspi32.exe" icon.
5. Follow the prompts.
6. Reboot and check for errors. If no errors shut down your system and go to the next
step.
Step E: Connecting the Scanner.
Warning! Ensure power is off when connecting or disconnecting any cables to the scanner or
workstation.
Setting the SCSI ID: The factory setting for the Scanner is 6, however, selecting a
different SCSI ID may be required when there are several devices on a SCSI chain.
Using a suitable tool, turn the selector switch until the arrow points to the desired ID
number (see figure 2-3). Setting the SCSI ID to 0, 1, or 7 is NOT recommended as these
settings are typically reserved for hard drives and the SCSI host adapter.
Setting Termination: The Fujitsu M3093GX\M3096G\GX\M3097G+\DG scanners come
with a plug in SCSI terminator (see figure below). The Fi-4340C\Fi-4640S\M4097D\Fi-
4750C\L scanners come with built in termination that is turned on or off through the
scanner panel. Termination for the Fi-4530C is handled automatically by the scanner. If
the scanner is the last device on the SCSI chain then the terminator should be placed on
one of the SCSI ports or turned on. If the scanner is not the last device on the SCSI
chain, then the terminator should be removed or turned off before connecting to the next
SCSI device.
Win95\98\ME Installation Procedure
.
Rev052104A