Indesit IDL 700 Manual de instalación y uso - Página 8

Navegue en línea o descargue pdf Manual de instalación y uso para Lavavajillas Indesit IDL 700. Indesit IDL 700 17 páginas. Indesit dishwasher installation and use

Imprimir página

Turning on the Appliance

How to start a wash cycle...

After performing all the operations described in the previous

paragraphs, turn the water tap on completely and press ON-

OFF button "A": you will hear a short beep and indicator

light "B" lights up. At this point, the appliance is on and

ready to be programmed

Starting and selecting the cycle.

Turn the cycle selector knob "D" clockwise until the reference

notch on the knob corresponds with the number or symbol

for the cycle you wish to set (consult the wash cycle table on

page 7, especially when first using the appliance).

If the appliance door is shut, press the Start button "R" and

you will hear a beep; the cycle will start up within a few

seconds.

Cycle phase indicator lights

The dishwasher is provided with 4 indicator lights "G" which

come on in sequence as the appliance is performing that

specific phase of the wash cycle.

These phases are:

pre-wash,

wash,

Cancelling or modifying a wash cycle in progress.....

Premise: You can cancel the wash cycle in progress, if it has

only just started.

To modify a wash cycle, keep the RESET button "R" pressed

for about 5 seconds: a prolonged beep will sound, followed

by three short beeps. Indicator light "G" will turn off and at

this point, all the settings will have been cancelled.

To select a new wash cycle, repeat the operations illustrated

in the paragraph entitled "starting and selecting the cycle".

If you have left out a dish...

You can interrupt a wash cycle by pressing the ON-OFF

button, then place the dishes you had left out into the

appliance, which will start up from where it was interrupted

when you turn it back on.

There's been a power failure? Have you opened the

dishwasher door?

The wash cycle stops and then restarts when the electricity

comes back on or when the door is shut.

At the end of the wash cycle....

The end of the wash cycle is indicated by two short beeps

and the flashing of the drying phase indicator light.

• Press button "A" to turn the appliance off.

• Turn off the water tap.

• Wait a few minutes before unloading the dishes: if you

wait a little while, they dry better thanks to the steam.

• Empty the lower rack first.

rinses,

drying

Warning: when you open the dishwasher door after the wash

cycle has just ended or is under way, take care not to scald

yourself with the hot steam.

You decide when it starts.

When you have loaded the dishes, you can choose when to

start your dishwasher before setting the wash cycle desired.

Press button "H" to delay the start of the wash cycle by 12,

9, 6 or 3 hours. Each time you press it, you will hear a short

beep and the indicator light "G" corresponding to the

selected delay will light up.

Now you can select the desired wash cycle. Press the start

button "R" and after you hear the beep, the countdown to

the delayed start will begin.

Once this time is up, the indicator light will stop flashing and

the wash cycle will begin.

If you have set a 12 hour delay, for example, once you have

selected the wash cycle, the 12 hour indicator light will flash

followed by the others in sequence until the set time delay is

up. A quick look at the indicator lights will keep you informed

of the countdown progress at all times.

Have you changed your mind?

If you change your mind, you can set a shorter time delay:

press button "H" to select it. You need not reset the wash

cycle.

If on the other hand you want to cancel the delay set and

you want the cycle to start immediately, press button "H"

repeatedly until the cycle starts and indicator light "G"

corresponding to the cycle start phase comes on.

Dual function of indicator lights "G"

1) flashing to indicate a delayed start: to remind you

that you have set a delayed start;

2) on and not flashing beneath the cycle phase symbol:

meaning the cycle has started and is in the phase indicated

by the symbol.

You want to wash on one rack only?

Remember to use half the amount of

detergent.

Your dishwasher also allows you to wash half a load, to save

water and electricity. Before setting any wash cycle, press

button "I", the indicator light "L" lights up.