Indesit IS50D1S Manual de instrucciones - Página 4

Navegue en línea o descargue pdf Manual de instrucciones para Cocinas Indesit IS50D1S. Indesit IS50D1S 12 páginas.

Imprimir página

regulation in force. The gas supply must be

connected to the left of the appliance. Be sure that

the hose does not pass through the rear of the

cooker touching hot parts.

! Make sure the supply pressure conforms with the

values shown in the table entitled "Caracteristics of

the burners and nozzles". When the cooker is

installed between cabinets (recessed), the

gas connection must be effected by an

approved flexible hose with bayonet fitting

(BS 669 Current Edition). The gas inlet for

the cookers is a threaded G 1/2 gas female

f i t t i n g .

Connecting the gas supply

To make the connection, a flexible hose should be

used corresponding to the current gas regulations

which are:

• the hose must never be at any point in its lenght

in contact with the "hot" parts of the cooker;

• the hose must never be longer than 1,5 metre;

• the hose must not be subject to any tension or

torsional stress and it must not have any

excessively narrow curves or bottlenecks;

• the hose must be easy to inspect along its entire

length to check its condition;

• the hose must always be in good condition, never

attempt to repair.

! The installation must comply with gas safety

(installation and use) regulations 1984. In all cases

for the above, by low, a qualified, corgi approved

engineer must be called for installation.

Electrial connection

Power supply voltage and frequency: 230-240V a.c.

50/60 Hz.

! ! ! ! ! The supply cable must be positioned so that it

never reaches at any point a temperature 50°C

higher than the room temperature. The cable must

be routed away from the rear vents. Should you

require it, you may use a longer cable, however, you

must ensure that the cable supplied with the

appliance is replaced by one of the same

specifications in accordance with current standards

and legislation.

that can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

Your appliance is supplied with a 13 amp fused plug

read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

When the cooker is

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-

wireable plug bearing the BSI mark of approval.

or:

• the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

! ! ! ! ! For appliances with a rating greater than 13 amp

(eg: electric hob, double ovens and freestanding

electric cookers etc.) the mains cable must be wired

into a cooker output point with a rating of 45 amp. In

this case the cable is not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket. Instructions for

connecting cable to an alternative plug:

! ! ! ! ! The wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow

- Earth

Blue

- Neutral

Brown

- Live

If the colours of the wires in the mains lead do not

correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked "E E E E E "

or or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked "L L L L L " or

coloured Red.

Connect Blue wire to terminal marked "N N N N N " or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a 13 amp fuse. A 15 amp plug must be

protected by a 15 amp fuse, either in the plug or

adaptor or at the distribution board. If you are in any

doubt about the electrical supply to your machine,

consult a qualified electrician before use.