Indesit KD3G11/G Manual de instrucciones de instalación y uso - Página 5
Navegue en línea o descargue pdf Manual de instrucciones de instalación y uso para Cocinas Indesit KD3G11/G. Indesit KD3G11/G 26 páginas. 50cm free standing dual fuel cooker
También para Indesit KD3G11/G: Manual de instrucciones (24 páginas)
Imprimir página
Gas connection
The cooker should be connected to the gas-supply by a corgi registered installer. During installation of this
product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience
of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be
carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable
to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed "Adaptation to
different gas types". On some models the gas supply can be connected on the left or on the right, as
necessary; to change the connection, reverse the position of the hose holder with that of the cap and replace
the gasket (supplied with the appliance). In the case of connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The gas supply must be connected to the left of the
appliance. Be sure that the hose does not pass through the rear of the cooker touching hot parts.
Important: make sure the supply pressure conforms with the values shown in the table entitled "Caracteristics of
the burners and nozzles". When the cooker is installed between cabinets (recessed), the gas connection
must be effected by an approved flexible hose with bayonet fitting (BS 669 Current Edition). The gas inlet
for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used corresponding to the current gas regulations which are:
the hose must never be at any point in its lenght in contact with the "hot" parts of the cooker;
•
•
the hose must never be longer than 1,5 metre;
the hose must not be subject to any tension or torsional stress and it must not have any excessively narrow
•
curves or bottlenecks;
•
the hose must be easy to inspect along its entire length to check its condition;
•
the hose must always be in good condition, never attempt to repair.
Important: the installation must comply with gas safety (installation and use) regulations 1984. In all cases for the
above, by low, a qualified, corgi approved engineer must be called for installation.
Electrial connection
Power supply voltage and frequency: 230-240V a.c. 50-60 Hz.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be accidentally
inserted into a socket. Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in accordance with the following code:
Green & Yellow
Blue
Brown
If the colours of the wires in the mains lead do not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked "E" or
Connect Brown wire to terminal marked "L" or coloured Red.
Connect Blue wire to terminal marked "N" or coloured Black.
A 15 amp plug must be protected by a 15 amp fuse, either in the plug or adaptor or at the distribution board. If you
are in any doubt about the electrical supply to your machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the following code:
BLUE
BROWN
GREEN AND YELLOW
HOT PARTS
- Earth
- Neutral
- Live
"NEUTRAL" ("N")
"LIVE" ("L")
"EARTH" ("E")
or coloured Green or Green & Yellow.
5