Indesit EDCE 85 B TM Manual de instrucciones - Página 15
Navegue en línea o descargue pdf Manual de instrucciones para Secadora Indesit EDCE 85 B TM. Indesit EDCE 85 B TM 16 páginas.
Imprimir página
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical
(see Assistance).
Assistance Centre
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
START/PAUSE
• The
button has not been pressed (see How to carry out a drying cycle).
• On machines equipped with "Locked" function, check the option is not enabled (see Programmes and options).
The drying cycle does not start.
• A delayed start time has been set (see Programmes and options).
START/PAUSE
• The
button has been pressed; a short delay follows before the dryer starts running. Wait for the drying cycle to
START/PAUSE
start; do not press the
Drying times are too long.
• The filter has not been cleaned (see Maintenance).
• The water container must be emptied? The "Empty water container" indicator light flashes and the message appears
(see Maintenance).
• The condenser needs to be cleaned (see Maintenance).
• The heat setting is not suited to the type of fabric to be dried (see Programmes and options).
• An incorrect drying time was selected for the type of load (see Laundry).
• The items are too wet (see Laundry).
• The air intake grille are clogged up (see "Installation" and "Care and Maintenance").
• The dryer is overloaded (see Laundry).
The "Empty water container" indicator light flashes, but the dryer has been running for a short time.
• The water container was probably not emptied before starting the programme. Do not wait for the signal for emptying the water
container, but always check and empty it before starting a new drying programme (see Description of the tumble dryer).
The "Empty water container" indicator light is on but the water container is not full.
• It is normal: the "Empty water container" indicator light flashes when the water container is full. If the indicator light is on but is
not flashing, it is just a reminder to empty the container (see Description of the tumble dryer).
The programme is finished but the items are damper than expected.
!
For safety reasons, the dryer programmes last a
dampness level required in
this interval, the dryer completes the programme and stops. Check the above points and repeat the
programme; if the items are still damp, contact the Technical Assistance Centre (see Assistance).
The code "F" appears on the display followed by one or two numbers, the options indicator lights and the pause indi-
cator light flash.
• If the display shows a fault, switch the appliance off and unplug it, then clean the filter and the Heat Pump Filter unit (see
Maintenance). Reinsert the plug, switch the appliance on and start another programme. If the display still visualises a fault, contact
the Technical Assistance Centre (see Assistance). If the display still visualises other numbers, mark the code and contact the
Technical Assistance Centre (see Assistance).
"dOn" briefly appears on the display every 6 seconds.
• The appliance is in "Demo" mode. Press the ON/OFF and
"dOn"
The display visualises
The "Remaining time" indicator changes during the drying cycle.
• The remaining time is constantly monitored during the drying cycle and is updated to show the best forecast. It is normal for
the displayed time to increase during the cycle.
The dryer is noisy during the first few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise persists during the entire cycle, contact
the Technical Assistance Centre.
The lights on the dryer control panel are off although the dryer is switched on.
• The dryer has gone into standby mode to save power. This occurs if you have left the dryer on or have had a power cut. It
occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Press the On/Off button and the lights will come on again.
button otherwise the dryer switches to the pause mode and the drying cycle will not start.
maximum of 5 hours. If an automatic programme has not detected the final
START/PAUSE
for 3 seconds, then the dryer starts functioning normally.
buttons and keep them pressed for 3 seconds.
EN
"h2o"
15