Kohler Intaglio K-2292 Manual de instrucciones de instalación - Página 2
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Sanitarios Kohler Intaglio K-2292. Kohler Intaglio K-2292 16 páginas. Countertop and undercounter lavatories
También para Kohler Intaglio K-2292: Manual del propietario (16 páginas), Manual del propietario (24 páginas)
Imprimir página
LOCATING THE FAUCET CENTERLINE
This lavatory is a unique installation with the faucet fittings mounted
on the countertop rather than on the lavatory itself.
The best location of the faucet centerline is determined by three
items: the size of the fitting or faucet spout escutcheons, length of
faucet spout, and clearance between the faucet spout and lavatory
rim.
FAUCET LOCATION
1.
Refer to Fig. #1 . Determine if the faucet spout escutcheon or
faucet handle escutcheon will be closer to the lavatory rim
when installed. Items to consider are the sizes of the different
faucet components and the lavatory shape. The escutcheon
found to be closest to the lavatory rim will be used in step 2.
X
Faucet Handle Escutcheon
Faucet Spout Escutcheon
2.
Measure the escutcheon, front-to-back, that was found to be
closest to the rim in step 1. This escutcheon measurement
may also be found on the faucet roughing-in page.
3.
Divide the front-to-back dimension in half, and add 1/4".
Standard sizes are shown in the chart on the next page. The
distance found will be used to draw the preliminary faucet
centerline.
NOTE: For all front to back dimensions, round up to the nearest
1/16" (2mm) if required.
FRONT TO
DISTANCE TO DRAW CENTERLINE
BACK DIMENSION
BEHIND REFERENCE LINE
2" (5cm)
1-1/4" (3.2cm)
2-1/8" (5.4cm)
1-5/16" (3.3cm)
2-1/4" (5.7cm)
1-3/8" (3.5cm)
2-3/8" (6cm)
1-7/16" (3.7cm)
2-1/2" (6.4cm)
1-1/2" (3.8cm)
B
1007251-2-
X
Lavatory Rim
Fig. #1
DRAW PRELIMINARY FAUCET CENTERLINE
NOTE: The following instructions refer to the installation of
Model K ---2332, in an above counter installation.
NOTE: Wall-mount faucet installations: Be sure to provide
sufficient spout overhang into the lavatory basin. Make sure that
the water stream is directed to the center of the lavatory and
there is sufficient hand washing clearance.
NOTE: Countertop faucet installations: Pay special attention
to the spout and handle fit clearance when locating the faucet, as
noted below.
Countertop faucet installations: Use the template to locate the
faucet spout hole centerline to provide adequate clearance between
the edge of the lavatory and the spout.
Refer to Fig. #2 . Check for adequate clearance between the back-
X
splash, faucet spout and handles and lavatory. Kohler recommends
clearance of at least 1" (2.5cm) between:
the installed lavatory and the faucet spout;
D
the installed lavatory and the end of the faucet handles
D
the faucet spout and handles, and the backsplash.
D
Refer to the faucet installation instructions for the required
clearance, and mark the preferred faucet hole locations.
Spout
Centerline
2
Backsplash
Cut-out
Line
Fig. #2
;
1"(2.5cm)
Minimum
Clearance
Outside Edge
of Lavatory
1-1/4"(3.2cm)
Minimum
Clearance
Kohler Co.