Kohler FLEUR WATERGUARD K-3417 AA Series Manual de instrucciones de instalación
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Aseos Kohler FLEUR WATERGUARD K-3417 AA Series. Kohler FLEUR WATERGUARD K-3417 AA Series 8 páginas. Vitreous china toilet
Imprimir página1. BEFORE YOU BEGIN
HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your partic-
ular installation. This will aid you in avoiding the unneces-
sary expense associated with improper installation. In
addition to proper installation, read all operating and safe-
ty instructions.
INSTALLER HAZARD NOTIFICATION
WARNING: Risk of injury or product damage.
Handle vitreous china products very carefully.
Vitreous china can break and chip if you
over-tighten bolts and nuts.
NOTE: Follow all local plumbing and electrical codes.
PRODUCT REQUIREMENTS
S
The toilet MUST have a 3/8" I.D. water supply that
is 10-1/4" above the floor and 5-1/8" left of the clos-
et flange centerline. 25 p.s.i. running pressure is re-
quired at the shut-off valve.
S
Since all toilets do not have the same supply rough-
in, you may have to change the location of the sup-
ply stop to install this toilet.
S
Closet flange must be 12" on-center from wall.
S
Seat post holes are on 5-1/2" centers.
MATERIALS REQUIRED
S
Closet flange
S
Toilet gasket (wax seal)
S
Toilet T-bolts (2) 5/16" diameter
S
Toilet setting compound (optional)
S
Toilet supply shut-off valve, 3/8" required
AA
112363–2–
(0793)
R
FLEUR WATERGUARD
VITREOUS CHINA TOILET
All information in these instructions is based on the latest
product information available at the time of publication.
Kohler Co. reserves the right to make changes in product
characteristics, packaging, or availability at any time with-
out notice.
These instructions contain important care, cleaning, and
warranty information please leave for the consumer.
PRODUCT PROPERTIES
S
Vitreous china 2-piece toilet.
S
Distance from rim to water surface is 6-3/4".
S
2" passageway.
S
For roughing-in and overall dimensions, see
Fig. #2.
S
Fixture dimensions are nominal and conform to tol-
erances by ANSI standards (A112.19.2).
ORDERING INFORMATION
Fleur Waterguardr Toilet Bowl
Tank with Tank Cover
. . . . . . . . . . . . . . . . .
Tank Cover
. . . . . . . . . . . . . . . . . . . . . . .
Bolt Caps
. . . . . . . . . . . . . . . . . . . . . . . .
Float Valve
. . . . . . . . . . . . . . . . . . . . . . . . .
Flush Valve
. . . . . . . . . . . . . . . . . . . . . . . .
Actuator
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat and cover
. . . . . . . . . . . . . . . . . . . . .
When specified:
3/8" supply
. . . . . . . . . . . . . . . . . . . . . . . .
Floor bolts (pr.)
. . . . . . . . . . . . . . . . . . . . . .
NOTE: For service parts ordering information, see sepa-
rate Service Parts document enclosed with product.
TOOLS REQUIRED
S
10" adjustable wrench
S
12" pipe wrench
S
Screwdriver
S
Tape Measure
S
Tubing cutter
S
Level
S
Putty knife
S
Hacksaw/metal file (for shortening T-bolts)
NOTE: Site preparation may require additional tools.
R
K-3417-**-AA
. . . . . . . .
K-4227-**-AA
K-4586-**-AA
80006-**-AA
52048-**-AA
30672-AA
500176-AA
500173-AA
82836-**AA
K-7638-AA
21401-AA
Copyright E1993 Kohler Co.