2N Telekomunikace EnergyBank Instrucciones de uso

Navegue en línea o descargue pdf Instrucciones de uso para Fuente de alimentación 2N Telekomunikace EnergyBank. 2N Telekomunikace EnergyBank 2 páginas.

Imprimir página

Solution: Connect the connectors properly, the swapping does not damage the equipment.

- When the adapter has been connected, yellow and, in some cases, green LEDs are lighted on EnergyBank, the

back-up equipment is supplied.

Cause: An unsuitable type of adapter, insufficiently low output voltage or current. This situation may happen

whenever EnergyBank is used with a unit other than a GSM gateway and available adapter.

Solution: Use a suitable adapter, the adapter output voltage must be in the whole range of load within the limits

included in the "Technical Parameters" section, the adapter current must be 200mA higher at least than the

maximum power consumption.

- EnergyBank has a substantially lower capacity during back-up despite of having been fully charged.

Cause 1: The usable capacity of accumulators decreases at higher discharge currents.

Cause 2: A deteriorated capacity of accumulators due to ageing.

Solution: Replace the accumulators.

- EnergyBank turns off when the backed-up equipment is turned on in the back-up mode.

Cause: The inrush current following the equipment turn-on made the accumulator voltage drop and EnergyBank

turns off.

Solution: Keep the equipment connected to EnergyBank continuously, never switch the backed-up equipment in

the back-up mode.

7. Technical Parameters

Input voltage:

11.5 to 14.5V

Pass-through loss at mains supply:

max. 0.5V

Maximum output current:

adapter output current minus 200mA, max. 1A

Accumulators used:

NiMh, size AA, 1800mAh, 10 pcs.

Self-consumption - off status:

30uA

Self-consumption - back-up status:

15mA

Self-consumption - charging:

max. 200mA

Charging current:

60 to 200mA (according to the battery charging level)

Accumulator voltage for low power:

11.3V

Accumulator voltage for turn-off:

10V

Dimensions:

170x130x45mm

Operational temperature:

0 to 45°C

EasyGate operation time in EnergyBank back-up mode (applies to new accumulators):

- Standby mode (70mA)

approx. 20 hours

- GSM in connection (200-300mA)

approx. 6 hours

Warranty for this device is 24 month, not valid for accumulators

___________________________________________________________________________________________

EC Declaration of Conformity

Directive: Electromagnetic compatibility

(EMC): 89/336/EEC

Manufacturer:

2N TELEKOMUNIKACE a.s.

Modřanská 621

143 00 Prague 4

Czech Republic

Declares that the product:

ATEUS

- EnergyBank

Type numbers: ATEUS

– EnergyBank,

501399E

Description: Backup power supply

Designed for: Backup power supply for 12V

powered devices

Conforms to the following Standards:

EMC: EN 55 024:1998, A1:2001, A2:2003

EN 55 022:1998, A1:2000, A2:2003,

A1/Cor.:2003, Cor.:2003

Date and place of issue:

Prague, Czech Republic, 17.3.2005

Manufacturer's stamp

...................................................

............................

Ing. Oldřich Stejskal, executive director

EnergyBank - Instructions for Use

1. Purpose

EnergyBank is designed to back up accidental supply voltage outages for equipment supplied with 12 V dc

voltage with the peak current drain of 1A. The backed-up power supply works as a pass-through system, i.e. the

backed-up equipment is connected continuously to the output connector and the power supply (typically a mains

adapter) to be backed up is connected to the input connector. During a voltage failure on the input connector,

EnergyBank transits automatically into the back-up mode.

Primarily, EnergyBank is designed to back up EasyGate and SmartGate GSM gateways made by 2N

TELEKOMUNIKACE (hereinafter referred to as GSM gateways). The backed-up power supply is connected

between the mains adapter and the GSM gateway, the adapter being included in the GSM gateway delivery.

- When a device other than a 2N gateway is used for back-up, it is necessary to observe the parameters included

in the "Technical Parameters" section. Especially, be sure to use an appropriate mains adapter. The adapter

voltage must be within the input voltage limits mentioned in the Technical Parameters; common transformer

adapters usually do not meet these requirements. The use of an unsuitable adapter may lead to a substantial

reduction of the battery life or equipment damage. You can purchase a suitable adapter with stabilised output

voltage from the 2N company.

- When your EnergyBank outlives its usefulness, dispose of it in accordance with applicable legal regulations.

2. Delivery Contents

- a backed-up power supply base board, including accumulators;

- screws and dowels for wall mounting;

- an EnergyBank - backed-up equipment interconnecting cable;

- a mounting pattern template and Instructions for Use.