Allied Telesis AT-WG101-15 Especificaciones
Navegue en línea o descargue pdf Especificaciones para Hardware de red Allied Telesis AT-WG101-15. Allied Telesis AT-WG101-15 1 páginas. At-wg100 series diplexers
Imprimir página
Datasheet |
Diplexers
AT -WG100 Series
Diplexers
AT -WG101-13
Diplexer with 1310TX/1550RX
AT -WG101-15
Diplexer with 1550TX/1310RX
(AT-WG101-13 and AT-WG101-15 must be
ordered together)
AT -WG102-13
Diplexer with 1310TX/1310RX
(Product must be ordered in pairs)
AT -WG102-15
Diplexer with 1550TX/1550RX
(Product must be ordered in pairs)
AT -WG103-13
Diplexer with 1310TX/1310RX
(Product must be ordered in pairs)
AT -WG103-15
Diplexer with 1550TX/1550RX
(Product must be ordered in pairs)
Double the Fiber Capacity
As stand-alone passive optical components, the
AT-WG100 Series diplexers enable the doubling
of fiber capacity by combining dual fiber strands
onto a single fiber strand.
AT-WG100 Series diplexers are used for multi-
plexing and de-multiplexing broadband and
narrowband wavelengths across a single fiber
strand. By consolidating transmission and receiving
paths, existing fiber pairs have the potential to
double the usable capacity.
Applicaiton
The AT-WG100 diplexer plugs directly into
existing single-mode fiber SC ports using
1310nm or 1550nm wavelengths. Most
USA Headquarters
|
19800 North Creek Parkway
European Headquarters
|
Via Motta 24
Asia-Pacific Headquarters
|
11 Tai Seng Link
www.alliedtelesis.com
© 2006 Allied Telesis Inc. All rights reserved. Information in this document is subject to change without notice. All company names, logos, and product designs that are trademarks or registered trademarks are the property of their respective owners.
commonly used in back-to-back scenarios, the
AT-WG100 Series can be used with a variety
of network equipment. A typical back-to-back
set up is depicted to the right.
Connectors
Single-mode SC
Performance
AT-WG101-13 & AT-WG101-15 Typical Maximum
Insertion Loss
Crosstalk from TX to RX
Crosstalk from common to TX -40dB
AT-WG102-13 & AT-WG102-15 Typical Maximum
Insertion Loss
Crosstalk from TX to RX
AT-WG103-13 & AT-WG103-15 Typical Maximum
Insertion Loss
Crosstalk from TX to RX
Environmental Specifications
Operating Temperature:
AT-WG101-13 & AT-WG101-15 -25°C to 75°C
AT-WG102-13 & AT-WG102-15 -40°C to 85°C
AT-WG103-13 & AT-WG103-15 -40°C to 85°C
Relative Humidity
Operating Altitude
Physical Characteristics
AT-WG101-13 & AT-WG101-15 10mm x 24mm x 64mm
AT-WG102-13 & AT-WG102-15 19mm x 36mm x 92mm
AT-WG103-13 & AT-WG103-15 19mm x 36mm x 92mm
Weight:
AT-WG101-13 & AT-WG101-15 26 grams
AT-WG102-13 & AT-WG102-15 32 grams
AT-WG103-13 & AT-WG103-15 32 grams
|
Suite 200
|
Bothell
|
|
6830 Chiasso
|
Switzerland
|
T: +41 91 69769.00
|
Singapore
|
534182
|
T: +65 6383 3832
AT-WG102 &
AT-WG103
0.8dB
1.4dB
-60dB
-50dB
-35dB
3.5dB
4.0dB
-60dB
-48dB
3.5dB
4.0dB
-60dB
-55dB
5% to 95% non-condensing
0 to 10,000 feet
WA 98011
|
USA
|
T: +1 800 424 4284
|
F: +41 91 69769.11
|
F: +65 6383 3830
AT-WG101
Key Features
•
Reduce fiber requirements up to 50%
•
Protocol & rate independent
•
Passive with low insertion loss
•
Multiplex & de-multiplex
•
Broadband or narrowband wavelengths
•
Lightweight
•
Simple to install
Ordering Information
AT-WG101-13
Diplexer with 1310TX/1550RX
AT-WG101-15
Diplexer with 1550TX/1310RX
(AT-WG101-13 and AT-WG101-15 must be ordered together)
AT-WG102-13
Diplexer with 1310TX/1310RX
(Product must be ordered in pairs)
AT-WG102-15
Diplexer with 1550TX/1550RX
(Product must be ordered in pairs)
AT-WG103-13
Diplexer with 1310TX/1310RX
(Product must be ordered in pairs)
AT-WG103-15
Diplexer with 1550TX/1550RX
(Product must be ordered in pairs)
|
F: +1 425 481 3895
617-00618-00 Rev. G