Dell 6100 Manual complementario - Página 4
Navegue en línea o descargue pdf Manual complementario para Servidor Dell 6100. Dell 6100 4 páginas. Dell poweredge 4200 servers: installation guide
También para Dell 6100: Instalación de bastidores (37 páginas), Manual de hardware (15 páginas), Instalación de bastidores (34 páginas)
![Dell 6100 Manual complementario](/uploads/products/server2/3182829/3182829.png)
The system reports that the total memory is 32 MB
less than the actual memory installed. For example,
if your system has 4 GB of memory, the system
reports only 4160512 KB.
Exit and save the system setup information.
NOTE: The value of Extended Memory is given in
kilobytes. To convert kilobytes to megabytes, divide the
kilobyte total by 1024.
If the total is incorrect, one or more of the DIMMs
may not be installed properly. Repeat steps 1 through
10. Make sure that the DIMMs are firmly seated in
their sockets.
11. Enter the system configuration utility. Then save
the system configuration information and exit the
utility.
Running the system configuration utility and saving
the system configuration information are required
for the system to recognize the newly installed
DIMMs. See Chapter 5, "Using the System Configu-
ration Utility," in the User's Guide for instructions on
running the utility and saving the configuration.
12. Run the RAM Test Group in the system
diagnostics.
See Chapter 5, "Running the System Diagnostics,"
in the Installation and Troubleshooting Guide for
information.
Installing DIMMs
The memory module has 32 DIMM sockets arranged in
four banks. Install DIMMs consecutively in groups of
four starting with socket J2.
NOTE: Use only DIMMs approved for use in this system.
______________________
Information in this document is subject to change without notice.
1997–1998 Dell Computer Corporation. All rights reserved. Printed in Ireland.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are registered trademarks of Dell Computer Corporation; Microsoft and
Windows NT are registered trademarks of Microsoft Corporation; and Novell and NetWare are registered trademarks of Novell Corporation. Other
trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer
Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
To install the DIMMs, use the following procedure.
CAUTION: Handle DIMMs carefully. Hold them
only by their edges. Do not slide them across any
surface. Applying too much pressure on retaining
clips can break the clips or damage the socket.
1.
Remove the memory module as described in
steps 1 through 4 of "Performing a Memory
Upgrade" found earlier in this section.
2.
Place the memory module flat, with the component-
side up and the memory module oriented with the
edge connectors toward you.
3.
Install the DIMM by orienting the pin-1 end of
the DIMM with the pin-1 end of the memory
module socket (see Figure 1).
4.
Hold the DIMM at a 90-degree angle to the mem-
ory module and press the DIMM carefully into a
socket until it is held by the retaining clips.
Check for proper installation by ensuring that there
is no gap between the retaining clips and the DIMM.
If the DIMM is not properly installed, remove it
according to the following removal procedure. Then
reinsert the DIMM into the memory module socket.
5.
Continue with steps 7 through 12 of "Performing
a Memory Upgrade" found earlier in this section.
Removing DIMMs
To remove the DIMMs, use the following procedure:
1.
Remove the DIMMs from the memory module by
starting from the highest-numbered socket.
2.
Open the retaining clips just enough to pull the top
edge of the DIMM away from the retaining clips.
3.
Pull the DIMM away from the socket, and store it
properly.