EarthWise CST00012 Manual del usuario - Página 4
Navegue en línea o descargue pdf Manual del usuario para Recortadora EarthWise CST00012. EarthWise CST00012 9 páginas. Cordless 18 volt string trimmer
También para EarthWise CST00012: Manual del usuario (8 páginas)
Imprimir página
OPERATING
CUTTING INSTRUCTIONS
Proper Cutting Siance
Weight should be balanced with both reet on solid ground.
with elbow lOCKed in
a
"slraight
position to \\i1!hstand any kickback force.
Basic Cutting Procedure
Slowly swing trimmer side-la-side as shown.
To convert for maintenance edging, turn off
the tool. Holding the trimmer with one hand by the auxiliary
handle, grasp the collar and push in the direction of arrow
and rotate the trimmer head unlillt stops (half tum), release
your hand, (rotate clockwise when viewed from the switch
end). The tool is locked in the edger position. Rotate the wire
edge guide forward and down into place before edging.
To operate as
a
maintenance edger, position trimmer above
sidewalk as shown.
.
,
Return to trimming position by turning the tool off, push in
direction of arrow and rotating the trimmer head counter
clockwise until it stops. When using the tool in the trimmer
mode you may choose to fold the wire edge guide up out of
the way.
.)
WARNING: Do not trim near electrical vMes or buildings.
LINE FEEDING
Your trimmer uses .065" (1.65mm) diameter nylon Une to cut
grass and weeds quickly and easily. In time, the tip of the
nylon line will become worn and the auto feed mechanism
will automatically feed and trim a fresh length of line. The
cutting Une will wear faster If the cutting is done
sidewalks or other abrasive surfaces
are
being cut. The line will extend approximately
;I.,
in. with each
stop and start of the switch trigger untn the line reaches Ihe
length of !he grass deflector blade. Do not bump unit on
ground in attempt to feed line or for any other purpose.
REPLACING SPOOL I CLEARING JAMS AND
TANGLED LINES
From lime
10
lime, especially when cutting thick or stocky
weeds, the line feeding hub may become clogged with sap
or other material and the line will become jammed as
a
resuH. To clearthe jam, follow these steps.
- Tum off the trimmer and remove the battery.
Press the release tabs on the line spool cover and remove
Ihe cover by pulling it straight off.
Lift the spool of nylon line out of the hub and clear any
broken line or cutting debris from the spool area.
In case of jams and tangled line, unwrap about one foot
(30cm) of line
to
ensure that it is undamaged, If it is
OK.
rewind it and insert the line end through the eyelet in the
spool hub. Pull the line through the hole to maintain tension
while placing the spool down in to the hub with the notched
side e)''Posed.
Press the spool down GENTLY and rotate it until you feel it
drop into place.
(When in place, the spOol will turn
a
few degrees left and
right freely.)
Snap the spool cover back on, insert the battery and turn
the tool on. In
a
few seconds
or
less you'll hear the line
being cut automatically to the proper length .
REWINDING SPOOL FROM BULK LINE
(USE ONLY .065" DIAMETER LINE)
Bulk line for your trimmer/edger is available at extra cos! farm
your local dealer or service center. To install, follow steps:
Turn off the trimmer and remove
the battery.
Press the release tabs on the line
spool cover as shown, and remove
the cover by pulling it straight off.
Remove the spool from the tool
and remove and discard all Une on
the spool.
Insert one end of the bulk line into the hole in the spool
as shown.
Hold the line in the hole and pull the rest of the line Ihrough
the slot in the spool as shown.
Snugly and evenly wind the bulk line onto the spool in the
direction of the arrow until il is
full.
Insert the line end through the
in the spool hub as
shown. Pull the line through the
to maintain tension
while placing the spool down into the hub with the notched
side exposed.
Press the spool down GENTLY and rotate it unfit you feel it
drop into place.
(When in place, the spool will turn a few degrees lef! and
lightfreely.)
Snap the spool cover oack on, insert the battery and tum the
tool on. In a few seconds or less you'll hear the nylon line
being cut automatically to the proper length.