Allmatic B.RO2 WALL Manual de inicio rápido - Página 2
Navegue en línea o descargue pdf Manual de inicio rápido para Transmisor Allmatic B.RO2 WALL. Allmatic B.RO2 WALL 5 páginas. Wall-mounted two-channel transmitter 433.92mhz rolling code
Imprimir páginaWall-mounted two-channel transmitter 433.92Mhz rolling code
DESCRIPTION
B.RO2 WALL is a wall-mounted two-channel transmitter 433.92Mhz rolling code. This roller code transmission makes remote control totally secure and grants immunity
from disturbs.
The switch panel can be used with receivers and control units of Birol series (f.i. RAPID, RAPID POWER, RAPID SMALL HELIOS, B.RO21W, etc.) and combines maxi-
mum effectiveness ease of installation and use for the comfort of your home.
EXAMPLE OF USE FOR ROLLER SHUTTERS :
SINGLE
COMMANDS
GROUP
COMMANDS
GENERAL
COMMAND
Each roller shutter can be operated by many B.RO WALL transmitters, up to 1000.- The transmitter can be recorded with roller shutter receiver through the learning mo-
dality shown in the instructions of the receiver.
This is a hidden button for remote learning of transmitters (unabled
through the programmer B.RO PRO, B.PRO BASIC o B.RO EPROG)
REMOTE LEARNING
1-With a nail push for 1 second the hidden button of an already re-
corded transmitter
2- Push for two seconds the button 1 of the transmitter you want to
learn This will be the button "OPEN", the other one which will be au-
tomatically recorded, will be the button "CLOSE".
WALL FITTING
•
Fit the holder (c) on the wall.
•
Sign on that surface the position of the screws 2,9x22 ( non supplied).
•
Drill and fix the nogs ( type S4 , non supplied) if necessary.
•
Fasten the pushbutton bulb (b) to the holder (c)
•
Hook the mask (a) to the pushbutton bulb (b)
EMBEDDED FITTING
The pushbutoon bulb of the transmitter (b) can be fitted in the two-module bulb
holder masks of the best markes and can be purchased separately.
Installation in this case has to be done taking advance from the hooking of the
pushbuttom bulb
Installazione a muro
A: Mask
B: Pushbutton
bulb
DIRECTIONS AND WARNINGS
•
The existence of metal parts or of damp walls may significantly reduce the range of the system.
•
As a rule, one should avoid, if possible, to install transmitters and receivers close to large metal articles or
near the ground and on the floor.
•
A remote control which does not provide visual monitoring of operation accomplishment may result in risks
depending on the employment mode. It is therefore wise to evaluate the consequences of incorrect use, and
minimise the opportunities for its occurrence.
GUARANTEE: The producer's guarantee is valid in compliance with the law, from the date stamped on the product and is limited to repiar work and free replacement of
pieces recognised as faulty for problems with the qualità and / or materials due to bad workmanship. The guarantee does not cover damages or defect due to external
causes, wrong maintenance practices, overload, normal wear, choice of the wrong product, wrong installation, or any cause for which the manufacturer cannot held
responsible. The guarantee is not valid if the product has been tempered with.
The data above mentioned are merely indicative. we all decline all responsability for range reductions or non-workings due to environmental interferences. The respon-
sability of the manufacturer for damages caused by accidents of any type due to its own defective products is solely the responsability provided by the italian law.
6-1622185 rev. 3 24/09/2012
B.RO2 WALL
Nogs S4
Screws2,9 x 22 TPS
C: Holder
DIN 7982 CH A2
ITA
ENG
SUBSTITUTION OF BATTERIES
•
Take away the mask (a) (only for wall fitting).
•
With a coin make lever on the fissure on the top of the pushbutton bulb (b),
and open it.
•
Replace the two batteries using exclusively lithium batteries Cr2016 paying
attention to the polarity. (Positive pole has to be connected to the metal pie-
ces).
•
Control triangular button covers.
•
Place the PCB on the buttons, the led should be oriented to the transparent
column.
•
Anchor the back cover controlling the orientation of the metal pieces for bat-
teries.
To replace batteries
open the transmitter
using a coin.
FRA
ESP
DEU
POR
The transmitter led is switched on while tran-
smitting of the code. If the battery of the tran-
smitter has run down, the led blinks while ope-
rating the device. In this case the battery has
to be replaced
Alloggiamento batteria
Pin for preventing
short circuit.
TECHNICAL FEATURES:
POWER SUPPLY
2 lithium batteries 3+3V
TYPE OF BATTERY
CR 2016 LITHIUM
ABSORPTION
5mA while transmitting
No. AVAILABLE CODES
18 bilions
No. AVAILABLE CHANNELS
2
ANTENNA
incorporated
OSCILLATOR TYPE
SAW
FREQUENCY
433.9MHz
WORKING TEMPERATURE
0° C ... 55° C
Pag. 1 di 1