Miller Auto Arc Manual del usuario - Página 9
Navegue en línea o descargue pdf Manual del usuario para Sistema de soldadura Miller Auto Arc. Miller Auto Arc 14 páginas. Pin welder
Imprimir página
4.
Be
sure
that
surface where
clip
is
to
be welded is
clean,
bare metal. Push resistance welder
against
surface until electrode
outer
ring
is seated
against
clean,
bare metal.
5.
Press Start switch for 0.5
to
1.0 seconds. There
should be
no more
than
1/8 to 1/4 in.
(3.1
to
6.3
mm)
discoloration around weld.
4-4.
SHRINKING/EXPANDING
High spots
and small dents
can
be smoothed
by using
the shrink electrode to
apply
heat
to
these
areas.
a
WARNING: Read
and follow
safety
Informa
tion
at
beginning
of entire Section
4
before
proceedIng.
1.
Install
shrinking
electrode
(see
Section
3-1),
and
plug
in
unit.
2.
Be
sure
that surface
to
be worked
on
is
clean,
bare
metal. Push resistance
welder
against
surface until
electrode
outer
ring
is seated
against
clean,
bare
metal.
3.
Press Start switch for 0.5 seconds
two
or
three
times to heat metal.
4.
If
a
high spot
does
not
shrink, tap
lightly
with
body
hammer. If
a
dent does
not
expand, carefuIIy~apply
a
damp
cloth
to
the heated metal.
4-5.
SHUTTING DOWN
Disconnect
input
power cord from
receptacle.
SECTION
5- MAINTENANCE & TROUBLESHOOTING
5-1.
ROUTINE MAINTENANCE
IMPORTANT:
Every
six months
inspect
the labels
on
this unit for
legibility.
Al!
precautionary
labels
must
be
maintained
in
a
clearly
readable
state
and
replaced
when necessary. See Parts List for
part
number of pre
cautionary
labels.
4~
WARNING: ELECTRIC SHOCK
can
kill.
Do
not
touch live electrical
parts.
Disconnect
input
power cord from power sup
ply receptacle
before
inspecting, maintaining,
or
servicing.
HOT SURFACES
can cause severe
burns.
Allow
cooling period
before
servicing.
Troubleshooting
of internal
parts
to be
per
formed
only by qualified
persons.
A.
Power
Cord
Every
three months
inspect
cord for breaks
in insulation.
Repair
or
replace
cord if insulation breaks
are
present.
Clean grease and moisture from cord
at
each
inspec
tion.
B.
Electrode MaIntenance
Keep
electrodes clean and
free of
grease and moisture.
Fine steel wool
can
be used
to
keep
electrode
parts
clean. A fine metal file
can
be used
to
keep
the
outer
electrode flat.
5-2.
TROUBLESHOOTING
a
WARNING: ELECTRIC SHOCK
can
kIll.
Do
not
touch live electrical
parts.
Disconnect
input
power cord from power sup
ply receptacle
before
inspecting, maintaining,
or
servicing.
HOT SURFACES
can cause severe
burns.
Allow
cooling period
before
servicing.
MOVING PARTS
can cause
serIous
Injury.
Keep
clear of
pinch points.
Troubleshooting
of internal
parts
to
be per
formed
only by qualified
persons.
It is assumed that the unit
was
properly
installed accord
ing
to
Section
3 of this
manual,
the
operator
is familiar
with the function of
controls,
the resistance welder
was
working properly,
and that the trouble is
not
related
to
the process. The
following
chart is
designed
to
diagnose
and
provide
remedies for
some
of the troubles that may
develop
in
this resistance welder.
If
the trouble is
not
remedied after
performing
these
pro
cedures,
contact
the nearest
Factory
Authorized Ser
vice
Station.
In all
cases
of
equipment
malfunction,
the
manufacturers
recommendations should be
strictly
fol
lowed.
118583
Page
5