Miller XMT 304 Manual del usuario - Página 7
Navegue en línea o descargue pdf Manual del usuario para Sistema de soldadura Miller XMT 304. Miller XMT 304 37 páginas. 4-rack and 6-rack
También para Miller XMT 304: Manual del usuario (40 páginas), Manual del usuario (26 páginas)
Imprimir página
1-3.
Additional
Symbols
For
Installation,
Operation,
And Maintenance
FIRE OR EXPLOSION hazard.
Do
not
install
or
place
unit
on, over,
or
near
combustible surfaces.
Do
not
install unit
near
flammables.
Do
not
overload
building wiring
be
sure
power
supply
system
is
properly
sized, rated,
and
protected
to
handle this unit.
FALLING UNIT
can cause
injury.
Use
lifting
eye
to
lift unit
only,
NOT
running
gear, gas
cylinders,
or
any other accessories.
Use
equipment
of
adequate capacity
to lift and
support
unit.
If
using
lift forks
to
move
unit,
be
sure
forks
are
long enough
to extend
beyond opposite
side of
unit.
OVERUSE
can cause
OVERHEATING
Allow
cooling period;
follow rated
duty cycle.
Reduce
current
or
reduce
duty cycle
before
starling
to weld
again.
Do not block
or
filter airflow
to
unit.
STATIC
(ESD)
can
damage
PC boards.
Put
on
grounded
wrist
strap
BEFORE
handling
boards
or
parts.
Use proper
static-proof bags
and boxes
to
store,
move,
or
ship
PC boards.
MOVING PARTS
can cause
injury.
Keep
away from
moving
parts.
Keep
away from
pinch points
such
as
drive
rolls.
WELDING WIRE
can cause
injury.
Do
not
press
gun
trigger
until instructed
to
do
so.
Do not
point
gun toward any
part
of the
body,
other
people,
or
any
metal when
threading
welding
wire.
MOVING PARTS
can cause
injury.
Keep
away from
moving
parts
such
as
fans.
Keep
all
doors,
panels,
covers,
and
guards
closed and
securely
in
place.
H.F. RADIATION
can cause
interference.
High-frequency
(HF.)
can
interfere with radio
navigation, safety
services, computers,
and
communications
equipment.
Have
only qualified
persons familiar with
electronic
equipment perform
this installation.
The
user
is
responsible
for
having
a
qualified
electrician
prompt
ly
correct
any interference
problem resulting
from the installa
tion.
If notified
by
the FCC about
interference, stop
using
the
equipment
at
once.
Have the installation
regularly
checked and maintained.
Keep high-frequency
source
doors and
panels tightly
shut,
keep
spark
gaps
at correct
setting,
and
use
grounding
and
shielding
to
minimize the
possibility
of interference.
ARC WELDING
can cause
interference.
Electromagnetic
energy
can
interfere with
sensitive
electronic
equipment
such
as
computers
and
computer-driven equipment
such
as
robots.
Be
sure
all
equipment
in the
welding
area
is
electromagneticallycompatible.
To reduce
possible
interference,
keep
weld cables
as
short
as
possible,
close
together,
and down
low,
such
as on
the floor.
Locate
welding operation
100 meters from
any sensitive elec
tronic
equipment.
Be
sure
this
welding
machine is installed and
grounded
according
to
this manual.
If interference still occurs, the
user
must
take extra
measures
such
as
moving
the
welding
machine,
using
shielded
cables,
using
line
filters,
or
shielding
the work
area.
I
OM-193
084
Page
3