Miller FT-1 Manual del usuario - Página 9
Navegue en línea o descargue pdf Manual del usuario para Accesorios de soldadura Miller FT-1. Miller FT-1 24 páginas.
Imprimir páginaFUMES AND GASES can seriously harm
your health.
•
Ventilate to keep from breathing fumes and
gases.
•
If ventilation is inadequate, use approved
breathing apparatus.
WELDING
WIRE
wounds.
•
Do not point gun toward any part of the body,
any conductive surface, or other personnel.
MAGNETIC FIELDS FROM HIGH CUR-
RENTS can affect pacemaker operation.
•
Wearers should consult with their doctor be-
fore going near arc welding, gouging, or spot
welding operations.
Welding wire and metal parts in contact with it
carry weld current when the gun trigger is de-
pressed and the welding power source contac-
tor is energized. See Owner's Manual for basic
welding safety information.
IMPORTANT: Every six months inspect the labels on
this unit for legibility. All precautionary labels must be
maintained in a clearly readable state and replaced
when necessary. See the Parts List for part number of
precautionary labels.
5-1.
GUN INSPECTION AND UPKEEP
WARNING: ELECTRIC SHOCK can kill; FLY-
ING FLUX PARTICLES can puncture eyes
and skin; WELDING WIRE can cause punc-
ture wounds.
•
Do not touch live electrical parts.
•
Shut down welding power source and wire
feeder and be sure they cannot be accidental-
ly energized before inspecting, maintaining,
or servicing gun.
•
Close air valve, bleed pressure from tank,
and disconnect air supply.
Usage and shop conditions will determine frequency
and type of maintenance required. At minimum, inspect
equipment every three months as follows:
1.
Inspect gun for broken areas, cracks and loose
parts; tighten, repair and replace as required.
2.
Carefully remove any weld spatter or foreign mat-
ter which may accumulate around the nozzle ori-
fice and inside nozzle.
3.
Repair or replace as required all hoses and
cables; give particular attention to frayed and
cracked insulation and areas where it enters
equipment.
can
cause
puncture
SECTION 5 – MAINTENANCE
1.
Assemble, install, and connect components as
applicable as instructed in Section 3.
2.
Make connections to welding power source as in-
structed in power source and wire feeder Own-
er's Manuals.
3.
Fill tank with flux as instructed in Section 3-5.
4.
Connect air supply to tank, open air valve, and
adjust pressure as instructed in Section 3-6.
5.
Energize wire feeder and welding power source.
6.
Begin welding.
4-2.
SHUTTING DOWN
1.
Shut down wire feeder and welding power
source.
2.
Close air valve, bleed pressure from tank, and
disconnect air supply.
4.
Remove grease and grime from components;
moisture from electrical parts and cables.
CAUTION: FLYING DIRT AND METAL PAR-
TICLES can injure personnel and damage
equipment.
•
Point gun liner only in a safe direction away
from personnel and equipment when clean-
ing with compressed air.
5.
Blow out the casing with compressed air when
changing wire. This removes any loose metal
chips and dirt that may have accumulated.
5-2.
FLUX SYSTEM UPKEEP
WARNING: ELECTRIC SHOCK can kill; FLY-
ING FLUX PARTICLES can puncture eyes
and skin; WELDING WIRE can cause punc-
ture wounds.
•
Do not touch live electrical parts.
•
Shut down welding power source and wire
feeder and be sure they cannot be accidental-
ly energized before inspecting, maintaining,
or servicing.
•
Close air valve, bleed pressure from tank,
and disconnect air supply.
IMPORTANT: Flux is very abrasive and has a wearing
and clogging effect on all parts and pieces exposed to it.
Good maintenance is essential for proper operation.
Usage and shop conditions will determine frequency
and type of maintenance required. At minimum, inspect
equipment every three months as follows:
1.
Using a soft brush or cloth, clean dirt and flux par-
ticles off all components.
OM-1542 Page 5