Diamond 350/GXS Manual de funcionamiento y mantenimiento - Página 6

Navegue en línea o descargue pdf Manual de funcionamiento y mantenimiento para Equipamiento alimentario comercial Diamond 350/GXS. Diamond 350/GXS 16 páginas. Professional slicer ce

Imprimir página

Diamond 350/GXS Manual de funcionamiento y mantenimiento

2.2 -

POSITIONING

Position the pallet, with the slicer, on a

flat surface and take off (a) the sharpe-

ner from the slicer (Fig. n°12).

At this point turn the machine on its

side (Fig. n°13) and unscrew, with the

proper wrench provided, the 4 nuts

which fasten the slicer. Remove the 4

washers and unscrew the 4 fastening

tie rods on the wooden pallet. Take off

the pallet and fasten the 4 feet provi-

ded. Finally, put the sharpener in its

place.

Position the slicer in the predestined

place.

The dimensions indicated in Tab. 1

(according to the model) must be kept

in mind for the plane where the slicer

will be installed, therefore it must be

wide enough, well-levelled, dry, smo-

oth, robust, stable about 80 cm high off

the ground and at least 20 cm from

walls, objects, shelves, etc. (Fig. n°14)

in respect to the space necessary for

its use and safeguarding.

Furthermore the machine must be pla-

ced in an environment with a maximum

humidity of 75%, not salty and with a

temperature between +5°C and +35°C;

in any case in environments which do

not lead to deviations of the above.

Make sure the graduated handgrip is in

posiion "0".

Check the alignment of the blade-plane

thickness gauge by running a finger

(Fig. n°16) from the blade towards the

thickness gauge plane (never in the op-

posite direction). Unscrew and screw

the foot (1) until the correct alignment is

found (Fig. n°17), then screw the rub-

ber part (2) to fix everything (Fig. n°17).

Fig. n°12

Fig. n°13

20cm

~ 80cm

Fig. n°14

Fig. n°15

Fig. n°16

Fig. n°17

2.3 - ELECTRICAL CONNECTION

Check that the data reported on the

technical-part number plate (Fig. n°18),

the delivery documents and the order,

correspond; contact the supplier for cla-

rification if they do not.

At this point make sure that the system

is standard and that the cable and

grounding system perfectly operate.

2.3.1 - Slicer with single-phase motor

The slicer is equipped with a feeding cable with a cross section area of 3x1mm²;

length 1.5m and a "SHUKO" plug. Connect the 230 V. - 50 Hz slicer,

interposing a magnetothermic differential switch of 10A,= 0.03A.

2.3.2 - Slicer with 400 V. three-phase motor

The slicer is equipped with a feeding cable with a cross section area of 5x1mm²,

length 1.5m and a red 15A 3F + T CEI plug. Connect the slicer to the 400 V. -

50Hz three-phase supply mains, interposing a magnetothermic differential switch

of 10 A, =0.03A.

2.3.3 - Slicer with 230 V. three-phase motor

The slicer is equipped with a feeding cable with a section area of 5x1mm²; length

1.5m and a blue 15A 3F + T CEI plug.

Connect the slicer 230 V. - 50 Hz three-phase supply mains, interposing a

magnetothermic differential switch of 10A,= 0.03A.

Check that the direction of the blade rotation is counter-clockwise looking at the

slicer from the side of the bladeguard. If not proceed as in par. 2.3.4.

2.3.4 - Blade rotation direction

Check the direction of the blade

rotation with a pulse of the "I" push-

button (ON), immediately followed by

the "0" push-button OFF.

The direction of the blade rotation must

be counter-clockwise when looking at

the slicer from the bladeguard side (Fig.

n°19). In the case that the rotation

direction is not exact, invert (Fig. n°20)

Fig. n°18

Fig. n°19