Diamond FVS-711/TS Manual - Página 7

Navegue en línea o descargue pdf Manual para Horno Diamond FVS-711/TS. Diamond FVS-711/TS 12 páginas.

Imprimir página

1.6 ELECTRICAL CONNECTION

When the appliance is delivered it is set to work at the voltage given

on the rating plate affixed on the right side of the appliance.

The effectiveness of the equipotential system of which the appliance is

part of, must conform to current standards.

Connect using the screw you find in the back side of the oven, marked

with the word EQUIPOTENTIAL.

The Manufacturer declines all and every responsibility if this important

accident prevention norm is not complied with. If the feeding cable is

damaged, it must be replaced by the technical service or in any case

by similar qualified personnel, in order to avoid any risk.

1.7 TECHNICAL DATA FOR ELECTRICAL CONNECTION

Model

4 x 2/3 GN

4 x 1/1 GN

7 x 2/3 GN

7 x 1/1 GN

11 x 1/1 GN

2.3 WATER FEATURES

The water must be suitable to human use with the following characteristics:

Temperature: included between 15 – 20°C

Total hardness: included between 4 and 12 °f (French degrees), it is advisable to install a softener upstream

from the appliance that will maintain the hardness level at the mentioned values.

Pressure: included between 150 and 250 KPa (1,5 – 2,5 bar).

Attention: higher water pressure values result in increased water consumption and can compromise

the correct functioning of some components.

Maximum chloride concentration (Cl-): less than 150 mg/litre.

Chlorine concentration (Cl2): less than 0.2 mg/litre.

pH: more than 7.

Water conductivity: included between 50 and 2000 µS/cm.

Attention: Water treatment systems that bring to different values to the ones above mentioned au-

tomatically invalidate the guarantee.

The use of dosing systems designed to prevent the build-up of lime-scale in pipes (i.e. polyphosphate dosing

systems) is also prohibited since it may impair the performance of the appliance.

2.4 TECNICAL DATA TABLE FOR THE WATER SYSTEM

Water flow rate regulator for steam

generation in combined and steam

cycle.

Water flow rate regulator drain steam

condenser.

Power loading

no. and motor

and voltage

4.3 kW

380-415 V 3N ~

50/60 Hz

2.7 kW

220-240 V 1N ~

50/60 Hz

5.2 kW

380-415 V 3N ~

50/60 Hz

5.2 kW

380-415 V 3N ~

50/60 Hz

8.8 kW

380-415 V 3N ~

50/60 Hz

15 kW

380-415 V 3N ~

50/60 Hz

4 x 2/3 GN

Ø 0.4 mm

Ø 0.7 mm

Heating

power

1 x 250 W

3.9 kW

1 x 250 W

4.9 kW

1 x 250 W

4.9 kW

1 x 250 W

8.5 kW

2 x 250 W

14.4 kW

4 x 1/1 GN

7 x 2/3 GN

Ø 0.4 mm

Ø 0.5 mm

Ø 0.7 mm

Absorbed

Feed cable

current

section

5 x 1.5 mm

7.5 A

3 x 1.5 mm

8.5 A

5 x 1.5 mm

8.5 A

5 x 1.5 mm

14.5 A

5 x 2.5 mm

25 A

5 x 4.0 mm

7 x 1/1 GN

11 x 1/1 GN

Ø 0.5 mm

Ø 0.7 mm