AquaScape AQUASURGE 3000 Manual - Página 4
Navegue en línea o descargue pdf Manual para Bomba de agua AquaScape AQUASURGE 3000. AquaScape AQUASURGE 3000 16 páginas. Skimmer and pondless waterfall vault pump
También para AquaScape AQUASURGE 3000: Instrucciones y mantenimiento (16 páginas)
Imprimir página
• Always operate the pump fully submerged; or if using
in-line, ensure a constant source of fresh water. Failure to
do so may overheat the pump and cause it to fail, voiding
the warranty.
• Use only in fully assembled state, paying particular
attention to ensure that both the outer and inner filter
screens are attached to the pump. Failure to operate the
pump without the filter screen will allow large debris to
enter the pump and cause the pump to fail, voiding the
warranty.
• Do not wear loose clothing that may become entangled in
the impeller or other moving parts.
• Keep clear of suction and discharge openings. DO NOT
insert fingers into pump with power connected.
• Do not pump hazardous materials or liquids, such as oil,
saltwater or organic solvents.
• Do not block or restrict discharge.
• Products returned must be cleaned, sanitized, or
decontaminated, as necessary, prior to shipment to
ensure that employees will not be exposed to health
hazards in handling said material. All applicable laws and
regulations shall apply.
Model Number
Maximum Flow Rate (GPH)
Maximum Head Height
Motor Type
Wattage
Amperage
Power Cord Length
Pump Discharge Diameter
Ideal Pipe Diameter
Pump Dimensions
Installation
• Do not submerge the
AquaSurge pump
directly into the pond.
The AquaSurge pump is
designed to be placed
inside a skimmer, Pondless
Waterfall Vault, sump or
basin. Please consider
Aquascape AquaForce
solids-handling pumps
(Ex. 1) if your application does not have a filter and
requires a pump that can be placed directly into the pond.
4
AquaSurge Pond Pump Specs
2000
2,193
12.5'
Asynchronous
160
1.3
20'
1.5" MPT
1.5" - 2"
12"L x 5.5"W x 7"H
AquaForce
®
Pond Pump
®
®
• The AquaSurge Pond Pump is a thermally protected,
submersible pump for outdoor or indoor use and has been
evaluated for use with water only.
IMPORTANT: Aquascape, Inc. is not
responsible for losses, injury, or death
resulting from a failure to observe these safety
precautions, misuse or abuse of pumps or
equipment.
AquaSurge Pond Pump Specifications
• Input Voltage: 120V AC
• Input Frequency: 60 Hz
• Submersible pump
• For outdoor or indoor use
• Thermally protected
• This pump has been evaluated for use with water only
• Input amps & wattage: see chart below
3000
3,196
15'
Asynchronous
165
1.4
20'
1.5" MPT
1.5" - 2"
12"L x 5.5"W x 7"H
• The AquaSurge pump is designed to be installed
horizontally on the rubber feet. The pump can also be
mounted vertically, if needed, by attaching the filter stand
ring on the outer filter screen, included with your pump
(Ex. 2).
Ex. 1
☎
☎
US (866) 877-6637 |
4000
3,947
18.5'
Asynchronous
Asynchronous
215
1.82
20'
1.5" MPT
1.5" - 2"
14"L x 6"W x 7.5"H
14"L x 6"W x 7.5"H
OR
CAN (866) 766-3426 | aquascapeinc.com
5000
5,284
24'
360
3
20'
1.5" MPT
2"
Ex. 2