Panasonic WV-SW395 Manual de instalación - Página 25
Navegue en línea o descargue pdf Manual de instalación para Videocámara Panasonic WV-SW395. Panasonic WV-SW395 40 páginas. Ip video cameras
También para Panasonic WV-SW395: Especificaciones (2 páginas), Folleto (2 páginas), Cuadro comparativo (6 páginas), Manual de instalación (40 páginas), Manual de instalación (40 páginas), Nota de integración (8 páginas)
Imprimir página
• 24 V AC power supply connector kit (accessory)
Recommended specification of cable (wire)
Wire size
#24
(AWG),
(0.22 mm)
(0.33 mm)
stranded
wire
Length of
20 m
cable
{65.62 feet}
{98.43 feet}
Power supply connector housing (accessory)
Pin No.
Signal
1
24 V AC LIVE (Brown)
2
24 V AC NEUTRAL (Blue)
3
Ground (Green/Yellow)
4
Not use
• How to assemble the power supply connector
Remove approx. 3 mm {1/8 inches} of the outer jacket of
the cable and twist the cable core to prevent the short cir-
cuit first.
Insert the tip of the cable into the point A of the contact,
and hold the cable using the cable clamp.
Approx. 3 mm {1/8 inches}
Upper
A
side
Contact
(accessory)
Procure either of the following tools for clamping.
Molex manual clamp tool:
57027-5000 (for UL1015), 57026-5000 (for UL1007)
After clamping the contact and the cable, insert the con-
tact properly into the power supply connector housing.
Upper side
Power supply connector housing (accessory)
Important:
• Conduct the electric conduit work after processing
the power supply connector and making sure that the
camera is operating normally.
#22
#20
#18
(0.52 mm)
(0.83 mm)
30 m
45 m
75 m
{147.64 feet}
{246.06 feet}
Cable
Insert
Cable
Contact
(accessory)
• Network cable
Connect a LAN cable (category 5e or better, STP*) to the
network connector.
* For Europe
Important:
• Use all 4 pairs (8 pins) of the LAN cable.
• The maximum cable length is 100 m {328 feet}.
• Make sure that the PoE+ device in use is compliant
with IEEE802.3at standard.
• When connecting both of the 24 V AC power supply
and the PoE+ device for power supply, 24 V AC will
be used for power supply.
Depending on PoE+ (or PoE) devices, the power sup-
ply indicator may light or the network functions may
be unavailable.
In this case, disable the PoE+ (or PoE) settings. Refer
to the operating instructions of the PoE+ (or PoE)
device in use.
• When disconnecting the LAN cable once, reconnect
the cable after around 2 seconds. When the cable is
quickly connected, the power may not be supplied
from the PoE+ device.
• The network camera is only intended for a connection
to an ethernet or PoE network without routing to the
outside plant.
• Output cable for the monitor used for adjustment
Connect a coaxial cable (BNC) (only for checking if images
are displayed on the monitor).
This output is provided only for checking the adjustment
of the angular field of view on the video monitor when
installing the camera or when servicing.
Important:
• The monitor out connector for adjustment is provided
only for checking the adjustment of the angular field
of view on the video monitor when installing the cam-
era or when servicing. It is not provided for recording/
monitoring use.
• Black bands may appear at the top and bottom or
right and left of the screen. (That does not affect the
adjustment because the angular field of view is not
changed.)
25