Diamond Audio Technology D6 1200.1 Manual de instalación - Página 5
Navegue en línea o descargue pdf Manual de instalación para Amplificador Diamond Audio Technology D6 1200.1. Diamond Audio Technology D6 1200.1 12 páginas. D6 series
Imprimir página
RCA Input and Pass-Thru Output - These RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the
1
source unit using RCA type audio cables, keeping them away from power wiring wherever possible. On the 4 channel amplifiers
(D6 700.4) "Front" and "Rear" input jacks are present. The"Pass-Thru" output allows the signal to pass on to other amplifiers.
The Pass-Thru output is unaffected by the onboard crossover.NOTE: D6 450.2, D6 700.4 and D6 1000.2 can accept speaker level in
through the RCAs. IMPORTANT! YOU MUST SWITCH THE INPUT TO HIGH WHEN USING SPEAKER LEVEL INPUT!
Input Gain Adjustment - This control matches the preamp stage of the DAT amplifier to your source unit. This is NOT a volume
2
control. The range is between 150mV and 4V for low setting and 1.5V to 14V in high setting when using speaker level input.
Input Selection (D6 700.4 Only) - This switch determines if you are using a front/rear input from either an aftermarket head unit
or a factory installed sytem (using the speaker level input). This is utliized so that you can "fade" from front to rear. If you chose
to ONLY use a single stereo input,(a single pair of Left and Right RCA's for example) then slide the switch to the "F" position. This
will then divert the signal to BOTH the front and rear inputs NOTE: in this position there will be NO fade!
Input Mode - This switch determines how the input is set-up. If you are utiliizing RCA outputs from an aftermarket head unit with
4
pre-outs, slide the switch to LOW. If you are using speaker leads as the "signal in" from a factory installed stock audio system
you MUST slide the switch to HIGH or you will overdrive the input stage causing serious damage.NOTE: this is NOT covered under
warranty. BE CAREFUL!!!!
Crossover Adjustment- Use this adjustment to select the crossover point. Remember that your choice will be directed to High
5
Pass or Low Pass depending upon the position of the adjacent switch.
Crossover Selection Switch - This switch allows you to select the crossover. Use High Pass for midrange or high frequency
6
speakers. Use Low Pass for subwoofers. In the OFF position, the crossover adjustment knob has no effect. The D6 1200.1 is only
available as Low Pass.
Sub-Sonic Adjustment - This control allows you to adjust the "pass-band" for a true 3 way speaker system. This helps solve
7
"standing wave" problems in-car (boomy bass), AND protects midrange/mid-bass drivers at the same time.
Phase Adjustment (D6 1200.1 Only) - This control allows you to adjust the "phase" so as to align the subwoofer in "time" to the
8
mids and tweeters. 0 to 180 degrees of adjustment capability. This is EXTREMLY useful to get the best and MOST bass out of
your system.
Bass Boost - This control adds 0 to +18dB (+12dB on 1200.1) of boost at 50Hz. Be cautious when adding boost to some subwoofer
9
systems as they may not be able to handle the additional low frequency boost. In the OFF position, no bass boost is added.
Remote Level Adjustment (D6 1200.1 Only) - This port is for the remote level control (included). The control is intended to allow
10
the user to control the level of gain up to the maximum adjustment level set on the amplifier. The control does not add additional
boost, it only attenuates the setting that is fixed at the amplifier's control panel.
Status LED's - These lights indicate when the amplifier is powered up normally and when there is a protection fault. See the
11
"Troubleshooting" section for details on what these useful indicators can tell you if there's a problem.
Power Input Connections - These connections are for input power, chassis ground, and remote turn-on. Use a minimum of 4 gauge
12
wiring for power and ground connections. The terminals will handle up to 4 gauge (D6 450.2/D6 700.4) and 2 gauge (D6 1000.2 /
D6 1200.1). Be sure any wiring that passes through metal has a grommet!
Power Fuses - Standard automotive type ATC/ATO fuses are used on DAT D6 Series Amplifiers. Always replace with the correct
1
fuse size. Never insert fuses of higher values. Doing so will void the warranty of your DAT amplifier. Also include a main fuse at
the connection to the vehicle battery within 18 inches (45.7 mm) of the positive battery post. It is also important to upgrade the
connection between the negative battery post and the chassis of the vehicle. This greatly reduces possibilities of weak electrical
"links" in the circuit.
Speaker Output Terminals - Connect your speakers to these terminals. Stereo connections are made as labeled. Bridged
14
connections use the LEFT + and RIGHT - as the two connections. The 2 and 4 channel amplifiers will perform into 2 Ohm stereo
loads or 4 Ohm bridged loads. DO NOT run 2 Ohm bridged loads on these amplifiers! The D6 1200.1 is the only amplifier in the
series capable of driving a load as low as 1 Ohm.
5