HP XP20000/XP24000 Nota de publicación - Página 8

Navegue en línea o descargue pdf Nota de publicación para Interruptor HP XP20000/XP24000. HP XP20000/XP24000 13 páginas. Hp storageworks xp disk array configuration guide: vmware (a5951-96106, september 2010)
También para HP XP20000/XP24000: Manual de integración (29 páginas), Nota de publicación (4 páginas), Manual del administrador (50 páginas), Manual de configuración (42 páginas), Manual de configuración (40 páginas), Manual de configuración (40 páginas), Manual de configuración (36 páginas), Manual de configuración (36 páginas), Manual de configuración (30 páginas), Manual de configuración (36 páginas), Nota de publicación (5 páginas), Manual de configuración (46 páginas), Manual de configuración (46 páginas), Manual de referencia (46 páginas), Manual de configuración (40 páginas), Manual de configuración (44 páginas), Manual de configuración (38 páginas), Manual de configuración (34 páginas), Manual de configuración (30 páginas), Manual de configuración (30 páginas)

Imprimir página

•

Optical transceivers. Only the HP 8Gb Short Wave FC SFP+ (part number AJ718A) is supported

for use in the HP StorageWorks 8/20q Fibre Channel Switch. This transceiver does not support

1 Gb/s port speed. If the port speed is configured as 1 Gb/s, the port is disabled and its state

will be changed to Downed. This can be corrected by configuring the port to a supported speed

(2 Gb/s, 4 Gb/s, 8 Gb/s, or auto-detect).

•

QuickTools stops responding after changing the switch's IP address. If you change the IP address

of a switch when using QuickTools to access that switch, the QuickTools session at the old IP address

stops responding. To access the switch with the new IP address using QuickTools, enter the new

IP address in a new browser window.

•

Java must be enabled in the browser for QuickTools to launch. If Java support or Java scripting

support is disabled in the browser, QuickTools will not launch. Ensure that Java support is enabled

and/or Java scripting support is enabled.

NOTE:

The scripting support is called Enable JavaScript in most browsers and Active scripting or Active

Web Content in Internet Explorer.

•

When running QuickTools, Java plug-in caching of temporary files and applets should be disabled.

Java caching can cause the wrong version of QuickTools to run. When running QuickTools, Java

plug-in caching of temporary files and applets should be disabled. If caching is enabled and a

different version of QuickTools is loaded from a switch, the version of QuickTools previously run

will load from the cache instead. Also, QuickTools could erroneously display the version number

just loaded from the switch.

NOTE:

If you have Java plug-in caching disabled and you upgrade your Java version, caching may

become enabled and will have to be disabled again.

•

Information from some devices connected to a switch is not displayed by QuickTools:

• Some connected device information, displayed by clicking the information icon (i) in the Details

column of the Devices Data window (accessed by clicking the Devices tab), is shown as Un-

defined or Data Unavailable. This usually occurs because the information is not provided

by the connected device. There are also some instances where the device model appears with

the Vendor name.

• Some connected device information displayed in the Vendor column of the Devices Data window

includes the device model with the Vendor name.

• The connected device information in the Target/Initiator column of the Devices Data window

is displayed as Unknown for the MSA1000, MSA1500, XP10000/12000, and

XP20000/24000.

•

Call Home to HP Services is now supported. Call Home to HP Services requires the 8/20q Fibre

Channel Switch to communicate with the HP Open Service Event Manager (OSEM) application.

The minimum required version of OSEM (version 1.4.5) has been released. Instructions to configure

Call Home to HP Services can be found in the HP StorageWorks 8/20q Fibre Channel Switch

installation and reference guide.

•

Deactivating a zoneset may cause reversion to soft zoning. Zoning is hardware enforced (hard

zoning) only when the following conditions are satisfied:

• A port/device is a member of no more than eight zones whose combined membership is 64

or less.