HP XP20000/XP24000 Manual de configuración - Página 18

Navegue en línea o descargue pdf Manual de configuración para Interruptor HP XP20000/XP24000. HP XP20000/XP24000 42 páginas. Hp storageworks xp disk array configuration guide: vmware (a5951-96106, september 2010)
También para HP XP20000/XP24000: Nota de publicación (13 páginas), Manual de integración (29 páginas), Nota de publicación (4 páginas), Manual del administrador (50 páginas), Manual de configuración (40 páginas), Manual de configuración (40 páginas), Manual de configuración (36 páginas), Manual de configuración (36 páginas), Manual de configuración (30 páginas), Manual de configuración (36 páginas), Nota de publicación (5 páginas), Manual de configuración (46 páginas), Manual de configuración (46 páginas), Manual de referencia (46 páginas), Manual de configuración (40 páginas), Manual de configuración (44 páginas), Manual de configuración (38 páginas), Manual de configuración (34 páginas), Manual de configuración (30 páginas), Manual de configuración (30 páginas)

Configuring Qlogic FCAs with the qla2300 driver

NOTE:

The qla2300 driver cannot be used with Sun StorEdge Traffic Manager/Sun Storage Multipathing.

To configure a Qlogic FCA using the Sun SAN driver stack, refer to

Configuring FCAs with the Sun SAN driver

Contact your HP representative to determine which QLogic FCAs and driver version HP supports with

the qla2300 driver. The qla2300 driver is not supported on x86 architecture. Configure Qlogic FCAs

with the qla2300 driver as follows:

Ensure you have the latest supported version of the qla2300 driver (available from

www.qlogic.com).

Edit the /kernel/drv/qla2300.conf driver configuration file to set up the FCA for a SAN

infrastructure:

hba0-connection-options=1;

hba0-link-down-timeout=30;

hba0-persistent-binding-configuration=1;

Persistent bindings are necessary in a fabric topology and are used to bind a SCSI target ID to a

particular WWPN (of an array port). This is required to guarantee that the SCSI target IDs will

remain the same when the system is rebooted. Persistent bindings can be set by editing the con-

figuration file or by using the Sansurfer utility. The following example illustrates the binding of

target 20 (hba instance 0) to WWPN 50060e8003285301 and the binding of target 30 (hba

instance 1) to WWPN 50060e8003285311:

hba0-SCSI-target-id-20-fibre-channel-port-name="50060e8003285301";

hba1-SCSI-target-id-30-fibre-channel-port-name="50060e8003285311";

(Replace the WWPNs above with the WWPNs for your array ports.)

With qla2300 v4.13.01 and earlier (legacy support on XP10000/XP12000):

If LUNs have been preconfigured in the /kernel/drv/sd.conf file, use the devfsadm command

to perform LUN rediscovery after configuring LUNs as explained in

"Defining the

With qla2300 v4.20, 5.02, or later:

Verify that the following entry is present in /kernel/drv/sd.conf:

name="sd" parent="qla2300" target=0;

Perform a reconfiguration reboot to implement the changes to the configuration files.

Use the /opt/QLogic_Corporation/drvutil/qla2300/qlreconfig –d qla2300 -s

command to perform LUN rediscovery after configuring LUNs as explained in

"Defining the

Applied Micro Circuits Corporation (AMCC) merged with Jaycor Networks Incorporated (JNI) and

discontinued their FCA hardware and software products. HP recommends to migrate to different FCAs.

Refer to the AMCC JNI Adapter End Of Life Customer Communication notice

Installing and configuring Sun Solaris for the XP disk array

paths" on page 21.

stack" on page 15.

http://

(http://