Panasonic SA-AKX910 Manual de instrucciones - Página 18
Navegue en línea o descargue pdf Manual de instrucciones para Sistema estéreo Panasonic SA-AKX910. Panasonic SA-AKX910 40 páginas.
Imprimir página
"CAN'T REC"
"DEVICE FULL"
•
You cannot do recording because the remaining recording
time of the USB device is less than the total time of the
music source. Change to a USB device which has enough
recording time and do the recording again.
•
You cannot do recording because the USB device is
write-protected. Remove the write protection of the USB
device and try again.
"ERROR"
•
An incorrect operation was done. Read the instructions and
try again.
"ERROR" (during recording)
•
You cannot select other playback source (example: radio,
USB etc.) or press [2/3] or [5/6] during
recording. Stop the recording function.
"F" / "F" ("" represents a number.)
•
The protection circuit has been activated and the system
may be switched off automatically.
•
Disconnect the AC mains lead and wait for a few seconds
before connecting it again. If the problem persists,
disconnect the AC mains lead and consult your dealer.
"INSERT USB B"
•
You cannot do recording because there is no USB device
connected to
USB B
"MEMORY ERROR"
•
The files in the internal memory can be corrupted. Switch off
the system and then disconnect the AC mains lead. Wait for
a minimum of 1 minute before switching on the system
again. If the problem persists, press [EDIT MODE] to select
"ALL DEL" to delete all albums in the internal memory and
do recording again.
"NO DEVICE"
•
You cannot check available storage space because there is
no USB device connected to
"NO DISC"
•
You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
•
There is no album or track in the USB device.
•
Examine the content. You can only play supported format.
•
The files in the USB device can be corrupted. Format the
USB device and try again.
•
The system may have a problem. Switch off the system and
then switch on again.
"NO TRACK"
•
There is no album or track in the internal memory.
"NOT SUPPORTED"
•
To use Karaoke effect in AUX source, set "AUX MODE" to
"MODE 1".
"PLAYERROR"
•
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REC ERROR"
•
You disconnected the USB device during recording.
Connect the USB device and do recording again.
•
An error occurred during USB recording. Disconnect the
USB device and then connect it again.
"REMOTE 1"
"REMOTE 2"
•
The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and [1]
for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and [2]
18
for a minimum of 4 seconds.
18
.
USB B
.
"TEMP NG"
•
The temperature protection circuit has been activated, and
the system will switch off. Let the unit cool down before
switching it on again.
•
Check that the ventilation opening of the unit is not obstructed.
•
Ensure this unit is well ventilated.
"TRK FULL"
•
The number of files has exceeded the supported limit.
"USB A NO DEVICE"
"USB B NO DEVICE"
•
The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
•
The USB device is drawing too much power. Disconnect the
USB device, switch off the system and then switch on again.
•
Check the connection, it may be caused by a faulty USB
cable.
"VBR"
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
Preparation
Press [SELECT <, >] repeatedly to select "AUX".
█ To set the code to "REMOTE 2"
1
Press and hold [SELECT] on the main unit and [2]
on the remote control until "REMOTE 2" is shown.
2
Press and hold [OK] and [2] for a minimum of
4 seconds.
█ To set the code to "REMOTE 1"
1
Press and hold [SELECT] on the main unit and [1]
on the remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [1] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [1] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
"– – – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.