Epever VS1024AU Manual del usuario

Navegue en línea o descargue pdf Manual del usuario para Inversor Epever VS1024AU. Epever VS1024AU 2 páginas. Au series

Imprimir página

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

※ Thank you for selecting ViewStar AU series solar charge

controller. Please read this manual carefully before using the

product.

ViewStar AU series solar charge controller

1. Overview

Thank you for selecting the ViewStar AU series common positive solar charge

controller. The VS-A controller is a PWM charge controller with built in LCD display that

adopts the most advanced digital technique. The multiple load control modes enable it can

be widely used on solar home system, traffic signal, solar street light, solar garden lamp,

etc. The features are listed below:

 Adopt high quality components of ST,IR and Infineon, make sure product using lifespan

 Terminals have UL and VDE certification, the product is more safer and more reliable

 Controller can work continuously at full load within the environment temperature range

from -25 to 55 ℃

 3-Stage intelligent PWM charging：Bulk, Boost/Equalize, Float

 Support 3 charging options: Sealed, Gel, and Flooded

 LCD display design, dynamically displaying device's operating data and working

condition

 Double USB design, the power supply charge for electronic equipment

 With humanized button settings, operation will be more comfortable and convenient

 Multiple load control modes

 Energy statistics function

 Battery temperature compensation function

 Extensive Electronic protection

2. Product Features

①

②

③ ④

Figure 1 Characteristic

①

LCD

②

MENU Button

③

RTS* Port

④

PV Terminals

※ USB output ports provide the power supply of 5VDC/2.4A and have the short

circuit protection.

Optional Accessory:

Name: Remote Temperature Sensor

Model: RTS300R47K3.81A

Acquisition of battery temperature

temperature compensation of control parameters, the

standard length of the cable is 3m (length can be

customized). The RTS300R47K3.81A connects to the port

③ on the controller.

NOTE: Unplug the RTS, the temperature of battery will be set to a fixed

value 25º C.

3. Wiring

Figure 2 Connection diagram

(1) Connect components to the charge controller in the sequence as shown above and pay

much attention to the "+" and "-". Please don't insert the fuse or turn on the breaker during

the installation. When disconnecting the system, the order will be reserved.

(2)After power on the controller, check the LCD on. Otherwise please refer to chapter

6.Always connect the battery first, in order to allow the controller to recognize the system

voltage.

⑤

⑥

⑤

Battery Terminals

⑥

Load Terminals

⑦

SET Button

⑧

USB Output Ports※

for

undertaking

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

(3)The battery fuse should be installed as close to battery as possible. The suggested

distance is within 150mm.

(4) The VS AU series is a positive ground controller. Any positive connection of solar, load

or battery can be earth grounded as required.

NOTE: Please connect the inverter or other load that it has the large start

current to the battery rather than to the controller, if the inverter or other

load is necessary.

4. Operation

4.1 Button Function

Button

MENU button

SET button

4.2 LCD Display

 Status Description

Item

PV array

⑧

⑦

Battery

Load

 Browse interface

NOTE：

1）

When no operation, the interface will be automatic cycle, but the follow two interfaces

not be display.

2） Accumulative power zero clearing: Under PV power interface, press SET button and

hold on 5s then the value blink, press SET button again to clear the value.

3） Setting temperature unit: Under battery temperature interface, press SET button and

hold on 5s to switch.

 Fault Indication

Status

Battery over

discharged

Battery over

voltage

Function

 Browse interface

 Setting parameter

 Load ON/OFF

 Clear error

 Enter into Set Mode

 Save data

Icon

Status

Day

Night

No charging

Charging

PV Voltage, Current ,Power

Battery capacity, In Charging

Battery voltage. current, temperature

Battery type

Load ON

Load OFF

Load Voltage, Current, Load mode

Icon

Description

Battery level shows empty, battery frame blink,

fault icon blink

Battery level shows full, battery frame blink, fault

icon blink