Olympus E-10 - 4MP Digital Camera Manual de inicio rápido

Navegue en línea o descargue pdf Manual de inicio rápido para Cámara digital Olympus E-10 - 4MP Digital Camera. Olympus E-10 - 4MP Digital Camera 2 páginas. Automatic pixel mapping feature
También para Olympus E-10 - 4MP Digital Camera: Manual de instrucciones (41 páginas), Manual de conexión (9 páginas), Instrucciones (1 páginas)

Imprimir página

Digital Camera

Quick Start Guide

Follow these simple instructions to start using your camera in minutes. Read the other

instructions provided with the camera for detailed descriptions of all the exciting features that the

Olympus E-10 packs into its compact design.

Important Parts and Names

1 Metering mode button

2 Drive button

3 Remote cable jack

4 Built-in flash

5 Flash button

6 Manual focus ring

7 Zoom ring

8 Exposure compensation button

9 Macro button

0 Flash synchro socket

A Focus mode switch

B Strap eyelet

C DC IN jack cap

D Monitor

E Eyepiece shutter lever

F Diopter adjustment ring

G Viewfinder

H Main dial

I Card cover

J Card cover lock

K SM/CF memory card button

L Card access lamp

M Light button

N AE lock button

O Power switch

P Mode dial

Q White balance mode button

R Sub dial

S Control panel

T Record mode button

U Flash mode button

V Hot shoe

W Video OUT jack

]

X USB connector

Y Monitor lock/release button

Z INFO button

[ Protect button

\ Erase button

[

] Arrow pad

^ OK button

a Menu button

b Monitor button

c Shutter button

d Remote control receiver/self-timer lamp

e Strap eyelet

f Battery compartment

g Tripod socket

h Lens

i Quick reference white balance button

j AF port

Ready!

You have to complete several important tasks before you can use the camera.

1 Attach the strap.

• Thread the ends of the strap through the eyelets on both sides of the camera. Slide the

ends of the straps through the sleeve and frame, and then pull them tight. Slide the sleeve

up the eyelets on both sides.

2 Load the lithium battery packs provided with the camera.

• On the bottom of the camera, turn the battery compartment knob to the open position

open the compartment, and then remove the battery case.

• With the +/ polarities aligned correctly, insert the battery packs into the battery, taking care

not to reverse the +/ polarity.

• Load the case in the camera. Push down lightly on the compartment case, and then move

the battery compartment knob to the close position

Note:

Your camera can also use the following types of batteries: AA (R6) Ni-MH (x4), AA (R6)

Alkaline (x4), AA (R6) Ni-Cd (x4), and lithium polymer (requires optional holder mounted on

the camera). For details, refer to the Reference Manual.

Caution:

Never use AA (R6) Zinc-carbon or AA (R6) lithium batteries with this camera. These batteries

could overheat and seriously damage the camera.

3 Insert the memory cards.

• The camera can hold one SmartMedia

and one CompactFlash

Either card can be installed alone or both can be installed together, but at least one memory

card of either type must be installed in the camera before you take pictures.

• Hold the camera with the lens facing away from you. On the back of the camera, move the

card cover lock button J up to open the card cover.

• To install a SmartMedia card, hold it with its notched corner down, and insert it into the

thinner slot closest to the back of the camera. Gently push the card completely into the slot.

(Insert the SmartMedia card until you can see about 2 mm of the card above the edge of

the slot.)

• To remove the SmartMedia card, push it in gently to release and then pull it out of the slot.

• To install the CompactFlash card, hold it with the arrow on the card toward you and insert it

into the wider slot closest to the front of the camera. Gently push the card completely into

the slot.

• To remove the CompactFlash card, gently press the eject button below the slot.

Caution:

Careful! If you press the eject button too hard, the CompactFlash card could pop out of the

slot.

4 Switch the camera on.

• The power switch is located on top of the camera by the mode dial (marked P, A, S, M).

Move the power switch toward you to the ON position. The control panel on top of the

camera comes on.

• The batttery check mark in the control panel on top of the camera tells you that the batteries

are fully charged. When this mark begins to blink, the batteries are low and you should

replace them as soon as possible. If this mark goes off, the batteries are dead and the

camera cannot be used until you have replaced the batteries.

• The large number to the right of the battery check tells you the approximate capacity of the

selected card. As each picture is taken, this number will decrease until it reaches 0 and the

card is full.

• To switch the camera off, move the power switch forward to the OFF position.

5 Set the date and time.

• On the top right corner of the camera, set the mode dial to the setup/connection mode mark

• On the back of the camera above the arrow pad, press the menu button

appears in the monitor.

• On the arrow pad, press

once to move the green highlight to the time setting mark

• With the time setting mark highlighted, press

mark. Below the date, the date format, -Y-M-D for example, where Y, M, D stand for the Year,

Month, Day, is displayed.

• Press

to select the date format (-Y-M-D, -M-D-Y, etc.), and then press

pointers appear above and below the first setting.

• Now you can set the date. On the arrow pad, press

digit number. With the desired number displayed (12 for example) press the OK button to

select the number and move the pointers to the next position. (The OK button is on the

lower right side of the arrow pad on the back of the camera.)

• For each position, press

to select the desired number and press the OK button to

save the setting and move the pointers to the next position. Be sure to set the time using

using the 24-hour settings. (00: 00~23: 59)

• After setting the minute, the green highlight returns to the time setting mark

OK button to save the settings and close the menu.

Get Set!

1 If the lens cover is on the lens, remove it.

2 Select the shooting mode.

• Move the mode dial to the P (Program mode) setting. With the mode dial set to P, the

camera automatically selects the correct aperture and shutter speed for the best exposure.

This is the best setting if you are just getting started.

Four shooting modes are available. For details, refer to the Reference Manual.

3 Adjust the viewfinder for your eyes. If you wear eyeglasses, you may need to

sharpen the viewfinder display.

(Type I or II) memory card.

• If the AF target mark in the center of the viewfinder is not sharp, turn the diopter adjustment

ring around the viewfinder left or right until the AF target mark is sharp.

4 Select the memory card.

• If only one memory card is installed in the camera, the card is selected automatically for

storing pictures that you take. If both cards are installed, the control panel display will tell

you which card is currently selected for storing pictures.

• If you want to switch the selection, press and hold down the SM/CF memory card button

below the control panel, and then turn the main dial (below the SM/CF memory card button

on the back of the camera) until you feel a click. In the control panel you should see SM or

CF displayed.

Go!

1 Make sure that the lens cover has been removed.

2 Take a picture.

• Point the camera at the subject that you want to take a picture, and look through the

viewfinder to compose the picture.

• Turn the zoom ring to enlarge or reduce the size of the subject in the viewfinder.

• The shutter button is near the top, front edge of the grip. With the picture composed in the

viewfinder, use the flat of your index finger to half-press the shutter button and wait for the

AF correct mark light in the lower left corner of the viewfinder to light. When you see the AF

correct mark light, the picture is correctly focused and exposure is calculated.

• Full-press the shutter button to take the picture. After the shutter releases, the monitor on

the back of the camera briefly displays the image of the picture you have just taken and

then goes off.

• If you see the

• On the left side of the camera, near the top, press the flash button to raise the built-in flash

unit. The flash will fire automatically to ensure correct exposure of the picture.

3 Repeat from Step 2 to take a few more pictures.

4 View the pictures that you have just taken.

. The menu

• Set the mode dial to playback

you will see the the last picture taken.

once to move the green highlight to the

• On the arrow pad, press

• If you want to display several images at once so you can quickly locate a picture, turn the

main dial to the left. Every time you move the dial left you will see 4, 9, then 16 frames in

. Two

the monitor. This is called the index display where each set of 4, 9, or 16 frames are

displayed as an index.

to increase or decrease the 2-

• Press

green highlight within the displayed index to select the picture that you want to display.

• If you want to enlarge the display so you can check the focus of the picture, turn the main

dial clockwise to enlarge the display in steps. As you enlarge the display, the view becomes

smaller. Press

main dial counterclockwise until the original display is restored.

5 Delete a picture.

. Press the

• With the frame that you want to delete displayed in the monitor, press the erase button

on the back of the camera near the bottom edge. If you are using the index display, use

erase button.

• To switch off playback, set the mode dial to P, A, S, or M.

Program mode

Camera selects the correct aperture and shutter

speed automatically.

Aperture priority mode

Camera sets the correct shutter speed for the

aperture that you select by moving the sub dial

left or right.

Shutter priority mode

Camera sets the correct aperture for the shutter

speed that you select by moving the sub dial left or

right.

Manual mode

You select the aperture with the main dial and the

shutter speed with the sub dial.

SmartMedia memory card selected.

CompactFlash memory card selected.

mark blinking in the viewfinder, this means that you should use the flash.

. The monitor on the back of the camera switches on and

to display the other shots one by one.

to display the next index. On the arrow pad, press

on the arrow pad to scroll around the enlarged image. Turn the

on the arrow pad to select the picture that you want to erase, and press the

to move the