Alphacom FP202 Manual del usuario - Página 2

Navegue en línea o descargue pdf Manual del usuario para Teléfono Alphacom FP202. Alphacom FP202 2 páginas.

Imprimir página

Location & Utilisation Of Controls

Park

Hook

Switch

Wall

Mount

Tone/

ETH TLB

Pulse

Mute

button

handset

Ringer pitch

control

Ringer volume

Store

control

Memory

Protection

Switch

(under inlay)

Utilisation Of Controls

The button functions are as follows:

0 - 9

- Dialling digits

* - #

- Dialling codes for MF Signalling

Recall

- For use on a PBX or for star services

Tone

- Switches from Loop Disconnect to DTMF during dialling

Save

- Used during conversation to store a memo number or

last number dialled in a separate memory allowing you

to make other calls before dialling this number again

Store

- Used to store a telephone number in memory

LNR

- Last number redial

Pause

- Pause function

Mute

- To prevent the other party from hearing you (ie. push

down (on handset) to mute) or, alternatively, on specially

adapted models this can be amended to push-to-speak.

In this instance, the phone will be clearly marked as

such

The switch functions are as follows:

Ring Vol (slide)

- Allows you to set the level of the ringer loudness

Ring Pitch

- Allows you to set the pitch of the ringer

ELR/TLB

- Sets the Recall to Earth (ETH) or

Time Loop Break (TLB)

LD/MF

- Sets the signalling (dialling) to Loop Disconnect (LD) or

DTMF (MF)

Memory Protection - Allows you to protect numbers stored in memory

location

Visual Indicators:

Ring

- This indicates an incoming call by lighting up.

Installation

Your FP202 telephone is designed to be plugged into the new phone sockets

adopted in the UK. The plug and socket are designed so that the plug will

only fit the socket the correct way round. Please note any other method of

connection will invalidate the instrument approval.

On any exchange line you may have as many sockets as you like, the number

of which may exceed the number of telephones. Your telephone can be

moved from socket to socket by simply plugging it in where you wish.

However, if you unplug your telephone whilst involved in initiating a call or

talking, the call may be lost.

There is a limit on how many telephones may be connected to an exchange

line at any one time. Plugging in too many telephones will overload your

exchange line and as a result your telephones may not ring. To enable you to

check if you are overloading a line, a Ringer Equivalence Number (REN) is

marked on the base of the telephones you wish to plug in. The ringers should

operate satisfactorily if the sum of the REN numbers are 4 or less. Include all

equipment provided. If a telephone is supplied unmarked you can assume it

to have a REN of 1, but this should be confirmed by your local sales office.

NOTE: NOT ALL TELEPHONES HAVE THE SAME REN VALUE.

This FP202 telephone has a REN of 1.

Once you have completed the "Initial Set-up Procedure" ( Section 4) then

plug your telephone into the socket. Once plugged in wait for 4 seconds

before making or answering a call.

Your FP202 telephone is now ready for use.

FP202 User Guide re-print.indd 2

Setting Dialling and Recall Mode

Two preset switches will be found situated in the battery compartment. These

are the DIAL MODE SELECTOR SWITCH , RECALL MODE SELECTOR

SWITCH, and should be set as follows:-

Memory

Keys

The Dial Mode Selector Switch

exchanges still operate on the PULSE dialling system. However, as new

exchanges are commissioned and older exchanges updated, the dialling

Ring

system is being changed to TONE dialling which gives faster connection as

Indicator

Recall

well as access to new services. Your FP202 telephone allows you to operate

Recall

on either system and the DIAL MODE SELECTOR SWITCH should be set to

Pause

the dialling mode required by your exchange. Set the switch to the LD (Loop

�

Save

Disconnect) position for PULSE dialling or to the MF (Multi Frequency) position

Save

for TONE dialling. If in doubt about the correct dialling mode used by your

Last number

LNR

redial

exchange, please consult your Network Operator.

Tone

The Recall Mode Selector Switch

to a TONE dialling exchange, set the switch to the TLB (Timed Loop Break)

position to enable you access certain Network Services. If you are connected

to a PULSE dialling exchange, set the switch to the ELR (Earth) position as

recall has no function on direct lines connected to such exchanges. (This will

avoid the possibility of cutting off your call should the recall button be pressed

accidentally.) If you are connected to a PABX, set the switch according to the

requirements of your particular PABX. If in doubt, consult your PABX

Instructions or your PABX maintainer. Set the switches, refit the battery

compartment cover ensuring that it clicks fully into place.

Setting The Ringer

The ringer volume control allows the ringer volume to be varied whilst still

allowing you to make calls. Set to minimum position the ringer will be off.

RINGER PITCH SWITCH - Set the switch to the HI, MED or LO position to

adjust the pitch of the ringer.

Connect To Telephone Socket

instructions have been completed, connect the plug at the end of the

telephone lead into the telephone socket. The plug will only fit the correct way

round.

Loop Disconnect or DTMF Dialling

will operate in Loop Disconnect (LD) or DTMF (MF) signalling depending on the

position of the switch located on the base of the telephone.

Manual Dialling

To make a call:

Last Number Redial

To redial the last number manually dialled: - Lift handset, listen for dial tone

Save Memory

telephone number you dialled into a Save memory location allowing you to

make other calls before trying the number again. To use this facility, press the

SAVE button. Replace the handset. To call the number, lift handset, await

dial tone and press the Save button. The number in the Save memory will

then be dialled automatically.

Memory Operation

of a maximum of 15 digits (including pauses or change of dial mode

instruction) may be stored in memory.

To store a number, please adopt the following procedure:-

Ensure that the telephone is plugged into the telephone socket, and that

the memory protection switch is positioned to the right. Lift handset.

Press STORE button once. Note that button only moves a short distance.

Enter the telephone number to be stored.

Press the STORE button again.

Press desired memory location button.

To protect the number stored ensure the memory protection switch is

positioned to the left.

- Many telephone

- If you are connected

- RINGER VOLUME SLIDE CONTROL

- When the setting up

- The FP202 telephone

- Lift handset, listen for dial tone

- Key in number you wish to call

- Press redial button

- This memory enables you to transfer the last

- Up to 20 telephone numbers each consisting

Operating Procedures

Storing Numbers whilst on a Call

- Numbers may also be

stored when you are actually in the process of making a call and using the

handset. This is useful, for example, if you are given a telephone number

during your conversation. The number may then be dialled from memory at a

later time. To store the number, press STORE button and then dial number,

press STORE button again and then desired memory location button. Write

down references to numbers stored against memory location buttons.

Changing a Number in a Memory Location

to change a number in a memory location, simply follow the instructions for

storing a number. Entering the new number will automatically erase the

previous number.

Dialling Numbers from Memory

- To dial a number from

memory, lift handset, await dial tone and press button corresponding to

memory location require. Sometimes it may be necessary to combine the

information from 2 memories or to combine memory dialling with manual

dialling. In these cases, simply press the 2 memory buttons in sequence or

press the desired memory button followed by manual dialling of the remainder

of the number. These combinations are often carried out when alternative

carriers are used.

Pause Button

- During a dialling or memory programming sequence

pressing pause will automatically insert a 2 second delay between the digits

3.6 second

dialled before and after pressing the Pause function. This may be neccessary

when using certain equipment or services.

Tone Button

- Pressing the Tone button during dialling when set to

Loop Disconnect (LD) switches the signalling from (LD) to DTMF (MF). This

facility may be used when the call is routed via multiple exchanges including

PBX where the first exchange responds to LD only whilst the distant exchange

responds to MF. Whilst the LD/MF switch is set to LD the telephone will reset

to LD when the handset is replaced back on hook.

Mixed Dial Mode Operation -

Storing Mixed Dial Mode Numbers

to an exchange requiring PULSE dialling and you wish to route your calls via

an alternative carrier (if available), it is necessary to dial an ACCESS code in

PULSE mode followed by a pause and then an AUTHORISATION code in

TONE mode. Since the telephone numbers of all calls to be routed via the

alternative carrier will have to be preceded by the same access and

authorisation codes, it is convenient to store them in a memory location.

Handset Mute Button

Whilst this is depressed the other party

will not hear the conversation. If specified the Executive FeatureSet 2

Memoryphone can be supplied with this button as 'push to talk', and in this

instance the telephone will be clearly marked as such.

Operating Procedure For PBX Connection

NOTE: The FP202 is suitable for connection to a PABX which returns

secondary proceed indication.

PBX Recall

- When connected to a PBX, the telephone will send a Recall

Signal to the exchange when the RECALL (R) button is pressed. This FP202

telephone provides either TIMED LOOP BREAK or EARTH RECALL Consult

you PBX supplier or maintainer to ascertain which is compatible with your

PBX. Having established which you require select either ELR (Earth Recall) or

TLB (Timed Loop Break) using the ELR/TLB switch.

N.B. Unlike the other keys the Recall key is a 'hard switch' not a 'soft press'

key. This means it will only depress slightly, and will remain depressed until

released.

PABX Pause Facility

- On PABX systems which provide secondary

proceed indication you must wait for the secondary proceed dial tone after

dialling the initial access digit(s), normally 9 for an outside line. For correct

operation of the Memory facilities it is therefore necessary to store a Pause

after the access digit to ensure correct dialling. Pressing the LNR key

automatically inserts a 2 second pause in the dialling sequence.

3.6 second

NB: Do not enter more than 1 consecutive pause. Failure to comply with

this may result in unsatisfactory operation and will invalidate the

approval.

General Use

- It must be noted that there is no guarantee of correct

working of this telephone in all circumstances when connected to a PBX. Any

difficulties should be referred to the telephone supplier. This telephone is

approved for connection to most PBX's. The supplier of this telephone

should be consulted for an up to date list of PBX's with which this telephone is

compatible.

- If you wish

- If you are connected

22/12/09 10:10:08