ABB ACS550-01 Manual de inicio rápido - Página 2

Navegue en línea o descargue pdf Manual de inicio rápido para Controlador ABB ACS550-01. ABB ACS550-01 2 páginas. Drive it low voltage ac drives 150...550 hp
También para ABB ACS550-01: Manual de inicio rápido (2 páginas), Manual del suplemento de instalación (16 páginas)

Imprimir página

Warning! For floating networks remove

screws at F1 and F2 on Frame sizes R5 or

R6.

Frame Size R5

GND

X0035

Power Input

Power Output to Motor

(U1, V1, W1)

(U2, V2, W2)

Optional Braking

Frame

Terminal

Brake Options

Size

Labels

R5, R6

UDC+, UDC- • Braking unit

• Chopper and resistor

Frame Size R6

X0013

GND

Power Input

Power Output to Motor

(U2, V2, W2)

(U1, V1, W1)

9. Install the cable clamp(s)

for the control cable(s).

(Power/motor cables and

clamps not shown in

figure.)

Wiring the Controls

1. Strip control cable sheathing

and twist the copper screen

into a pig-tail.

2. Route control cable(s)

through clamp(s) and

tighten clamp(s).

3. Connect the ground screen

pig-tail for digital and analog

I/O cables at X1-1.

4. Connect the ground screen

pig-tail for RS485 cables at

X1-28 or X1-32.

5. Strip and connect the individual control wires to

the drive terminals. For details, or other

configurations, see "Control Connections" in

the User's Manual.

SCR

Signal cable shield

AI1

Ext. freq. ref. 1: 0...10 V

AGND

Analog input com.

10V

Ref. voltage 10 VDC

AI2

Not used

AGND

Analog input com.

AO1

Output freq.: 0...20 mA

AO2

Output current: 0...20 mA

AGND

Analog output com

10 24V

Aux. volt. output +24 VDC

11 GND

Aux. volt. common

Digital input com. for all

12 DCOM

Start/Stop: Active = start

13 DI1

Fwd/Rev: Active = rev. dir.

14 DI2

Constant speed sel.

15 DI3

Constant speed sel.

16 DI4

Ramp pair: Active = 2

17 DI5

18 DI6

Not used

19 RO1C

Relay output 1

20 RO1A

Default operation:

Ready = 19/21 connected

21 RO1B

22 RO2C

Relay output 2

23 RO2A

Default operation:

Running = 22/24 connected

24 RO2B

25 RO3C

Relay output 3

26 RO3A

Default operation:

Fault(-1) =25/27 connected

27 RO3B

(Fault => 25/26 connected)

Note 1. Jumper setting:

AI1: 0...10 V

AI2: 0(4)...20 mA

Note 2. Code: 0 = open, 1 = connected

DI3

DI4

Output

Reference through AI1

X0006

CONSTANT SPEED

6. Install the conduit/gland box cover (1 screw).

Check Installation

Before applying power, perform the following

checks.

Environment conforms to specifications.

The drive is mounted securely.

Proper cooling space around the drive.

Motor and driven equipment are ready for start.

Floating networks: Internal RFI filter

IP2003

disconnected.

Drive is properly grounded.

Input power (mains) voltage matches the drive

nominal input voltage.

The input power (mains) terminals, U1, V1, W1,

are connected and tightened as specified.

The input power (mains) fuses / mains switch

installed.

The motor terminals, U2, V2, W2, are

connected and tightened as specified.

Motor cable is routed away from other cables.

NO power factor compensation capacitors are

connected to the motor cable.

Control terminals are wired and tightened as

specified.

NO tools or foreign objects (such as drill

shavings) are inside the drive.

NO alternate power source for the motor is

connected – no input voltage is applied to the

output of the drive.

Re-install the Cover

ramp pair.

1. Align the cover

and slide it on.

2. Tighten the

captive screw.

3. Re-install the

control panel.

Apply Power

Always re-install the front cover before turning

power on.

Warning! The ACS550 will start up

1 (1202)

automatically at power up, if the external

2 (1203)

run command is on.

3 (1204)

1. Apply input power.

When power is applied to the ACS550, the

green LED comes on.

Note! Before increasing motor speed, check that

the motor is running in the desired direction.

Check

Start-up

In Start-up, enter motor data (collected earlier)

and, if needed, edit parameters that define how

the drive operates and communicates.

Assistant Control Panel

The Start-up Assistant steps through typical

start-up selections, and runs automatically

upon the initial power up. At other times, use

the steps below to run the Start-up Assistant.

1. Use the MENU key to

access the Menu list.

2. Select Assistants.

3. Select Start-up Assistant.

4. Follow the screen

instructions to configure

the system.

Note! For common parameters and menu items,

use the Help key

descriptions.

If you encounter Alarms or Faults, use the

Help key or refer to the Diagnostic section

of the User's Manual.

Basic Control Panel

The Basic Control Panel does not

include the Start-up Assistant. Refer

to the Start-up Section of the User's

Manual and manually enter any

parameter changes desired.

IP2009

LOC

400RPM

1200 RPM

12.4 A

405 dm3/s

DIR

12:45

to display