Arca-Swiss Cube Manual de inicio rápido - Página 2

Navegue en línea o descargue pdf Manual de inicio rápido para Accesorios para cámaras Arca-Swiss Cube. Arca-Swiss Cube 2 páginas.
También para Arca-Swiss Cube: Instrucciones (2 páginas)

Imprimir página

The Functions :

Quickset device

(1)

Panning locking

lever (4)

Top panning

(3)

Friction

adjustment

longitudinal

(8)

Control knob tilt

Bottom panning

longitudinal

(7)

The Cube is mounted through the 3/8" thread in the bottom panning (10) onto the

tripod. The turning inner circle of the bottom panning (10) must rest upon a hard, flat

surface.

The camera is installed onto the ARCA-SWISS quickset device (1).

The movement of the camera is effected inside the circular arc, thus a change of the

object distance as well as the image selection hardly develops. Through loosening the

panning locking lever (11) of the bottom panning (10) the desired image selection is

determined and locked. Depending on the kind of image, the camera becomes in one

or both axles longitudinal transverse aligned by means of the spirit levels.

The manual base tilt (9) is used for camera angles of 30° and above. The range 0-30°

should be made by the geared longitudinal control knobs (7). With slope angles under

30° the manual base tilt must be (9) engaged in the zero-position and fixed.

After adjustment and leveling of the camera, the top panning (3) can be rotated while

the camera remains leveled. The panning locking lever (4) locks the top pan (3). The

basic friction of the tilts (transversal/longitudinal) using heavy cameras can be

adjusted with the grey friction adjusting wheels (6, 8).

If the base friction is correctly adjusted, the camera can be adjusted only by the control

knobs (5, 7, 9) or by pushing manually the movement at the Cube head.

ARCA-SWISS quick release device

All tripod heads from ARCA-SWISS are available with a choice of quick release: Classic,

flipLock® and monoball®Fix. The Classic and flipLock® systems are equipped with a

double dovetail so that you can fit the classic camera plates in the upper dovetail and the

monoball®Fix to the bottom. The Fix system is compatible with the monoball®Fix plates.

All three of them are compatible with the monorails of the ARCA-SWISS cameras.

Classic

monoball®Fix

ARCA-SWISS

camera plate

monorail unit

monoball®Fix

Classic instructions :

To open, turn the knob counterclockwise.

To close, turn the knob clockwise.

Spirit-level

(2)

adjustment

transversal

Control knob tilt

transversal (5)

Panning locking lever

(10)

(11)

flipLock®

monoball®Classic

camera plate

Friction

(6)

Manual

base tilt

(9)

The movement of the camera is effected inside the circular arc, thus a change of the

flipLock

instructions :

To switch from the locked position to the sliding position :

1. Pull the release button between your two fingers towards you.

2. Swing the lever 90°.

To switch from the sliding position to the filly opened position :

3. Unlock the system by pulling the coged axis with your thumb.

4. Swing the handle fully.

Release button

Coged Axis

Coged wheel to adjust width (you must press the

flipLock manually together to adjust the wheel)

Extension

bracket

CAUTION: The ARCA-SWISS flipLock® mechanism requires camera plates with similar

tolerances (width) to lock camera plates securely. DO test all your camera plates if they lock

securely with an adjusted flipLock® device !

ARCA-SWISS refuses explicit any liability for consequential damage to camera equipment

mounted on third party camera plates not manufactured by ARCA-SWISS.

monoball®Fix instructions :

1. Open by pulling the clamping lever with your thumb

2. Insert the cameraplate (side opposite the clamping lever)

3. if necessary, center the cameraplate

4. important: lock by clicking on the clamping lever !

Tilt Longitudinal & Transversal ± 30°

Base tilt 60°

object distance as well as the image selection hardly develops.

Base & Longitudinal tilt 90°

click !