Arcam DiVA AVR100 Manual - Página 11

Navegue en línea o descargue pdf Manual para Receptor Arcam DiVA AVR100. Arcam DiVA AVR100 17 páginas. Surround sound receiver
También para Arcam DiVA AVR100: Esquemas de servicio (13 páginas)

Imprimir página

VOLUME control

To adjust the volume level of the loudspeakers, pre-amp outputs

and headphones use the

VOLUME

shown in the display while it is being adjusted. Three seconds

after the volume is adjusted, the display reverts to show the

selected input.

Note that different sources may require different settings of the

control to achieve the same perceived volume level.

VOLUME

The volume can be controlled from 0dB over 80 steps.

BASS and TREBLE controls

Turn the bass and treble controls clockwise to boost response

or anticlockwise to cut response. For a ﬂ at response leave the

controls in the 12 o'clock 'notched' position.

Pressing the

button bypasses the bass and treble

DIRECT

controls and gives a small improvement to sound quality. If

you do not wish to alter the bass or treble controls, we

recommended that you select

DIRECT

Using the tuner

The AVR100's radio tuner can be controlled from the upper row

of front panel buttons (see diagram, below) or from the remote

control handset (see 'Using the remote control').

FM MUTE/

PRESET/

RDS INFO

MONO

STORE

TUNE

DOWN/UP

Tuning to a station

Pressing the PRESET/TUNE button toggles between the two

tuning modes of the unit – 'Preset' or 'Tune'. The selected mode

is brieﬂ y shown in the display.

Preset mode

•

In Preset mode, press the

and

•

(or

on the remote control handset) to cycle up and

P–

P+

down the preset stations.

See 'Storing a preset' and 'Deleting unused presets', below.

Tune mode

In Tune mode:

•

Press the

and

buttons on the front panel (or

•

on the remote control handset) for longer than half-a-

P+

second to engage automatic tuning. The tuner searches

for a radio station signal of sufﬁ cient strength and stops.

To skip to the next station, press one of the buttons

again. Automatic tuning is available for both the FM and

AM bands.

Tapping the

•

and

buttons engages manual tuning. This

•

can be used for tuning to a speciﬁ c frequency. It is also

useful if you are trying to select a station that is too weak

for the auto search mode.

Regardless of the mode used to tune your AVR100, when it is

accurately tuned to a station '

TUNED

•

control. The volume level is

SPEAKERS

STEREO

buttons on the front panel

P–

•

' lights up in the display.

DOLBY PRO LOGIC

SPEAKERS

VIDEO 1

after 3 seconds

DOLBY PRO LOGIC

SPEAKERS

VIDEO 1

MHz

Storing a preset

To store a preset, tune to the radio station you wish to store.

Press the

button: this causes 'MEMORY' to ﬂ ash in the

STORE

display. Now select the preset number you wish to assign to

the station using the

•

and

buttons on the front panel (or

•

on the remote control handset). Press the

P–

P+

button again.

Once the preset is stored, the display reverts to show the

station name (if RDS information is transmitted) or its frequency.

To quit the memory function without storing a preset, leave the

tuner controls untouched for ten seconds. It is also possible to

overwrite a stored station by saving another in its place. There

are thirty presets available for FM use and ten for AM use.

Your presets are retained for several weeks (but not indeﬁ nitely),

when the AVR100 is disconnected from the mains supply.

Deleting an unused preset

Press the

button, then select the preset number you

STORE

•

want to delete using the

and

buttons (or

•

the remote control handset), followed by the

button.

The display brieﬂ y shows 'DELETED' and '– –' is shown in

place of the preset number. You can reactivate a deleted preset

number by storing a station in the normal way.

CH dB

STORE

P–

P+

FM MUTE/MONO

AVR100