Arcam fmj UDP411 Manual - Página 4

Navegue en línea o descargue pdf Manual para Reproductor Blu-ray Arcam fmj UDP411. Arcam fmj UDP411 13 páginas. Blu-ray disc player arcam fmj udp411

Imprimir página

Making audio connections

The UDP411 offers a number of alternatives for connecting audio. The connection type to use depends on the rest of

your system; chose the type most appropriate to your amplifier.

If you want to listen to

... we recommend the following:

audio through...

Your television

How you listen to audio through your TV depends on the inputs it has and your

video connection:

HDMI: If you are using an HDMI connection (not DVI), this will carry both

audio and video. No further connection is required.

Digital Audio (Coaxial or Optical): If your TV has Digital Audio inputs on

Coaxial or Optical connectors, connect the appropriate digital audio lead

between the TV input and the appropriate UDP411 digital output. Do not

make a connection between the UDP411 and a TV's Digital Audio output.

Stereo phono: If your TV has stereo phono inputs, follow the instructions

below for a stereo amplifier.

Your stereo amplifier

If you wish to listen to audio from your player through a stereo amplifier, then use

the stereo analogue outputs. These outputs provide a stereo down-mix of the source

material.

Using a stereo phono cable of a suitable length, connect the outputs labeled

to the left and right inputs (respectively) for DVD or CD on your

ZONE 1 AUDIO

amplifier.

Your surround-sound receiver

Connect the HDMI output to your receiver (for audio and video) if the receiver

supports audio over HDMI. The HDMI connection supports all possible audio

formats including Dolby TrueHD, DTS Master Audio and multichannel PCM.

If your receiver does not support HDMI audio, connect one of the Digital Audio

outputs (Optical or Coaxial) to the 'Blu-ray' , 'BD' or 'DVD' input of your receiver.

These digital outputs provide PCM, Dolby Digital, DTS or MPEG multi-channel

audio, depending on the source material. The UDP411 can also be set to re-encode

all audio to DTS ('Bitstream Mixed') (see ' A udio' on page E-17). This option

provides the best surround sound quality for Digital Audio connections.

You may also wish to connect the stereo analogue audio outputs to the CD input on

your receiver, for listening to CDs. This will allow the UDP411's audiophile digital-

to-analogue circuitry to be utilised, for the best stereo sound quality.

E-6

The HDMI interface

If you have a HDMI- or DVI-equipped monitor

or display, you can connect it to the UDP411

using a HDMI cable. The HDMI connector carries

uncompressed digital video, as well as digital audio.

About HDMI

HDMI (High Definition Multimedia Interface) supports

both video and audio on a single digital connection

for use with Blu-ray Disc players, digital TV, set-top

boxes, and other AV devices. HDMI was developed to

combine the technologies of High-bandwidth Digital

Content Protection (HDCP) and the Digital Visual

Interface (DVI) in one specification, with the addition

of transmission of digital audio information; HDCP is

used to protect digital content transmitted to DVI-

compliant displays.

HDMI has the capability to support standard or

high-definition video, together with stereo or multi-

channel surround-sound audio. HDMI features include

uncompressed digital video, one connector (instead of

several cables and connectors), and communication

between the AV source and AV devices.

Connecting using HDMI

Use a HDMI cable to connect the

socket on

HDMI

this player to a HDMI socket on a compatible display

device or receiver. The arrow on the cable connector

body should be face up for correct alignment with

the connector on the UDP411. If the UDP411 video

resolution has been configured to 'HDMI Auto' , then the

UDP411 will configure its video output automatically to

match the capabilities of the attached HDMI device.

NOTE

A HDMI connection can be made only with HDMI

or DVI-equipped components compatible with both

DVI and HDCP. Note that if you choose to connect

to a DVI device, you will need an adaptor (HDMI to

DVI) to do so; a DVI/HDCP connection, however,

does not support audio signals.

If you require further information on the possibilities

for connecting your UDP411 to your DVI/HDMI

equipped display device, please contact your Arcam

dealer.

Troubleshooting HDMI

Problems with video

Problems with audio

The type of audio provided by the HDMI connector

No video (blank screen)

depends on the configuration of the UDP411 (see

Check that the HDMI cable is connected correctly

' A udio Setup' on page E-17). Choose a setting according

at both ends. If an HDMI-equipped A/V receiver

to the capabilities of your audio system. Note that

is in use, try connecting the UDP411 directly to

pure DVI devices (connections requiring a HDMI to

the display device, in order to isolate where the

DVI converter cable) do not support audio via this

fault may lie.

connection.

Check that the display device is set to display the

HDMI input (i.e., has not been set to some other

video input, instead).

Check that the HDMI input of the receiver and/or

display device is enabled. See the user handbook

of the connected device for details on doing this.

Using an alternative video display device (e.g.,

connected via the composite video out), check

that video is output.

Consult the user handbook of the display device

to ensure that it can handle the output formats

provided by the UDP411. The UDP411 can

provide the following:

720 x 480p (NTSC progressive scan)

1280 x 720p

720(1440) x 480i (NTSC interlaced)

1920 x 1080i

720 x 576p (PAL progressive scan)

1920 x 1080p

720(1440) x 576i (PAL interlaced)

3840 x 2160p

At least one of these standards must be supported by

the connected device in order for it to work with the

UDP411.

No video (random noise)

Random noise will be displayed if the content-

protection algorithm fails to authenticate the attached

device. This will occur, for example, if a DVI device that

does not support HDCP (such as a computer monitor)

is connected to the UDP411.

To attempt to isolate this problem, remove all discs from

the UDP411, then power-off both the UDP411 and the

connected display device. Switch the display device on,

then the UDP411 – at this point, the idle logo of the

UDP411 should be shown on the display device. If this

is not the case, please check the items listed above for a

blank screen.

If the noise appears when a copy-protected disc

(Blu-ray/DVD) is played, then it is the authentication

that is failing. Please contact your dealer for further

information.

E-7