AXXIOM TERAVALVE XL Manual de funcionamiento y mantenimiento
Navegue en línea o descargue pdf Manual de funcionamiento y mantenimiento para Unidad de control AXXIOM TERAVALVE XL. AXXIOM TERAVALVE XL 2 páginas.
Imprimir página
WARNING
1.
Any person intending to operate this equipment or any person intending to be in the vicinity during its operation that cannot read
or completely understand all of the warnings, operating procedures and instructions, and the rules for safer operation contained in
this manual must receive proper training from their supervisor and/or employer. Consult Axxiom Manufacturing, Inc.
2.
Do not operate any abrasive blaster or blast equipment before reading and completely understanding all the warnings, operating
procedures and instructions, and the rules for safer operation contained in this manual.
3.
Do not operate any abrasive blaster or blast equipment without following the rules for safer operation and all the operating
procedures and instructions. Failure to properly use blast equipment could result in serious injury or death.
4.
Do not perform any maintenance while any abrasive blaster or blast equipment is pressurized. Always depressurize any vessel
before loading media or performing any maintenance.
5.
Do not use abrasives containing free silica. Silica can cause silicosis or other related respiratory damage. You must wear personal
protective equipment for all abrasive blasting operations. Observe all applicable local, state and federal safety regulations in
conjunction with airline filters and respiratory protection. Reference OSHA (Occupational Safety and Health Administration).
6.
Do not enter areas during abrasive blasting operations without breathing protection. All personnel in the vicinity of abrasive
blasting operations should wear NIOSH approved air fed respirators, hoods or helmets.
7.
Do not modify or alter any abrasive blaster, blast equipment or controls thereof without written consent from Axxiom
Manufacturing, Inc.
8.
Do not use bleeder type deadman valves on any Schmidt® abrasive blasters. The use of A-BEC, Clemco or a similar bleeder type
deadman valve can cause unintentional start-up without warning, which can result in serious personal injury.
9.
Do not sell, rent, or operate abrasive blasters without remote controls. OSHA regulations require remote controls on all blast
machines. Failure to use remote controls can cause serious injury or death to the operator(s) or other personnel in the blasting
area. (Reference OSHA regulations.)
10. Do not repair or replace any portion of Schmidt equipment using components that are not Schmidt original replacement parts.
Use of replacement components that are not Schmidt original replacement parts may result in equipment failure which can result
in serious personal injury and will void all warranties.
11. RULES FOR SAFER OPERATION
11.1 KNOW YOUR EQUIPMENT. Do Not operate this equipment in a manner other than its intended application. Do Not operate this
equipment without following the Rules for Safer Operation and all the operating procedures. Failure to do so could result in serious injury
or death.
11.2 RECEIVE PROPER TRAINING. Do Not operate or perform maintenance on this equipment unless you have received operational and
maintenance training. Begin by thoroughly reading and understanding this document and any operational and maintenance manual or
instructions for the equipment that will be used in conjunction with the Thompson Valve®. Consult an authorized Schmidt® or Axxiom
distributor.
11.3 USE PROPER PERSONAL PROTECTIVE EQUIPMENT. Do Not operate or perform maintenance on this equipment without
wearing OSHA approved eye, ear, foot, and lung protection.
11.4 ADHERE TO ALL REGULATIONS. Do Not operate or perform maintenance on this equipment without observing all local, state, and
federal safety regulations including, but not limited to, OSHA (Occupational Health and Safety Administration).
11.5 USE CORRECT REPLACEMENT PARTS. Do Not use replacement parts that are not manufactured by Axxiom Manufacturing, Inc.
and furnished by an authorized distributor of Axxiom Manufacturing, Inc. Incorrect replacement parts can result in equipment failure and
cause serious injury or death.
11.6 SAVE THIS OPERATION AND MAINTENANCE MANUAL.
Refer to this operation and maintenance manual as well as any other manufacturers information included for equipment that is used in
conjunction with the Thompson Valve. Never permit anyone to operate this equipment without having him/her first read this manual and
receive proper training. Provisions should be made to have this manual readily available to the operating and maintenance personnel. If for
any reason the manual becomes lost or illegible, have it replaced immediately. This operation and maintenance manual should be read
periodically to maintain the highest skill level; it may prevent a serious accident.
TRADEMARKS, PATENTS, AND PROPRIETARY STATEMENTS
Schmidt, the Schmidt S logo, MV2 Valve, Thompson Valve, and Combo Valve are registered trademarks owned by Axxiom
Manufacturing, Inc. Use of these trademarks without the written consent of Axxiom Manufacturing is strictly prohibited. Products
manufactured and marketed by Axxiom Manufacturing, Inc. are protected by patents issued or pending in the United States and other
countries. The text, diagrams, and drawings contained in this manual are proprietary information intended solely for instruction in the
operation of the specified equipment. Use of any text, diagrams, or drawings contained in this manual for any reason other than its intended
purpose without the written consent of Axxiom Manufacturing, Inc. is strictly prohibited.
TERAVALVE XL®
OPERATION AND MAINTENANCE MANUAL
January 2018
SAVE THIS MANUAL AND MAKE AVAILABLE
TO ALL USERS OF THIS EQUIPMENT!
Manual Part Number 7200-325
(Available for downloading from schmidtabrasiveblasting.com)
XX
Copyright © 2018 A
IOM Manufacturing, Inc.
11927 S. Highway 6, Fresno, Texas 77545
800.231.2085 * 281.431.0581 * fax 281.431.1717
Visit us at www.schmidtabrasiveblasting.com