Creek Company ODC 816 Instrucciones de montaje - Página 4

Navegue en línea o descargue pdf Instrucciones de montaje para Barco Creek Company ODC 816. Creek Company ODC 816 4 páginas.

Imprimir página
ODC 816™
Your ODC Outdoor Discovery Craft is designed to give you many years of service.
IF YOU EVER HAVE ANY QUESTIONS OR PROBLEMS WITH YOUR ODC 816 PLEASE DO NOT
RETURN IT TO THE DEALER YOU BOUGHT IT FROM. PLEASE CONTACT THE CREEK COMPANY
DIRECTLY TOLL FREE AT 1-800-843-8454. WE ARE OPEN M-F 9AM-5PM MOUNTAIN TIME. OR CONTACT US VIA
HIN
(HULL IDENTIFICATION NUMBER) IS LOCATED ON SQUARE TUBING OF SEAT SUPPORT FRAME MEMBER
1. Always wear a US Coast Guard approved personal flotation device when in your ODC 816
2. Never float alone.
3. Always check your ODC 816
use your craft.
4. Never use your craft if you suspect the Air Bladders, Frame, Oar Components and Pontoons Covers has been damaged.
5. Never overinflate your ODC 816
6. Never use you ODC 816
1. If your Air Bladder is losing air, please check that valve assembly and top valve cap are fully seated. Reseat valve
assembly and repeat pontoon inflation instructions.
2. Do not store your ODC 816
3. If you are leaving you ODC 816
inside the pontoons to a dangerous level. Let some of the air out of the Pontoons if the craft will be out of the water in the sun
for any length of time, or if it is stored in a vehicle, etc.
4. A gain in altitude will increase the pressure in the Pontoons also. If you are taking your inflated ODC 816
to a high elevation, be sure to let some of the air out of it.
5. For short term storage, we recommend you let some air out of your Pontoons.
6. For long term storage, we recommend you make sure your ODC 816
in a cool dry area.Do not store your wet ODC 1018
other component damage.
7. Repairing bladder, use enclosed patch kit. Identify puncture. Fully deflate bladder.
clean and dry area around puncture. Apply glue to puncture area and patch using
applicator straw Press patch over puncture area. Allow 24 hours to dry, before inflating.
8. Note: Metal parts may rust and are not covered under warranty.
9. We recommend the use of electric trolling motors only on your ODC 816
10. Do not use the cargo deck as a standing platform. It is not designed for this and may break
if used in this capacity.
Accessories are available for your ODC 816
The Creek Company Ltd. , PO Box 773892, Steamboat Springs, CO 80477
All Creek Company products are guaranteed against defects in material and workmanship for the life of the product to
the original owner. This does not cover damage due to misuse or normal wear and tear.
O O U U T T D D O O O O R R D D I I S S C C O O V V E E R R Y Y C C R R A A F F T T
Please follow inflation instructions and warnings carefully.
AND ON RIGHT RIGHT SIDE CARGO DECK (SEE FIGURE 1)
Warning:
Please read and follow carefully.
™
Air Bladders, Frame, Oar Components and Pontoons Covers for possible damage before you
™
.
™
without the Air Bladders fully inflated.

CARE AND MAINTENANCE:

™
in direct sunlight.
™
out in the sun for any amount of time, be aware that the heat can increase the pressure
™
or visit the Creek Company Store at www.CreekCompany.com
970-879-5221 • fax 970-879-7577 • email: [email protected]
Specifications and other details subject to change without notice.
™
is completely dry, deflated and stored out of the sunlight
in freezing temperatures as this may result in frame and
™
.
™
. Ask for them where you bought your ODC 816
Made in China
™
™
.
™
from a low elevation
™
,