FIAMA F20 Manual de usuario y mantenimiento - Página 3
Navegue en línea o descargue pdf Manual de usuario y mantenimiento para Monitor FIAMA F20. FIAMA F20 7 páginas. Display with internal battery power supply and hollow shaft rotative transducer
También para FIAMA F20: Manual de usuario y mantenimiento (8 páginas)
Imprimir página
Display for rotative transducer
Installation
Before installing the instrument, read the following warnings:
a) Connect the instrument strictly following the instructions of the manual.
b) It is the responsibility of the user to check, before using, the correct settings of the parameters of the
instrument to avoid damage to persons or things.
c) The instrument CANNOT function in a dangerous environment (inflammable or explosive).
d) The unit has sensible parts to electrostatic charge, therefore the handling of the inner electronic cards has
to be carried out with appropriate care to avoid permanent damages.
Description
The F20K – EN20M is a dimension-display complete of hollow shaft position transducer in order to carry out
a complete device for measuring linear or angular shiftings.
The display has 7 digits besides a sign (range from -9999999 +9999999), with 10 mm-high-digits allow a very
good readability also by distances.
It is possible to select the count direction, the position of the decimal point, and the measure unit (mm, inches
ore degrees).
The displayed value may be correct through a programmable multiplicative factor with values ranging from
0,00001 to 999999.
The dimension display may be carried out either in absolute or in incremental mode by simply pressing the
suitable key; this allows relative measuring within the measuring field. It is also possible to set a preset
dimension that may be recalled through the suitable key.
There are also available 3 distinct origins for the correction of quota by using different tools and the offset
function for balancing of tool wear. On the display all activated functions are showed by a symbol. The keys
enabling to recall the preset dimension and the absolute/relative dimension switches may be inhibited in a
very simply way.
On the display all activated functions are showed by a symbol.
The power supply is internal with 2 batteries type AA of 1,5V, one-year-life. The run-down of battery is
indicated with occasional blinking, 1 month before the complete flat the indication remains on; the battery has
to be changed, in very easy way and without loosing quota, while the machine is standing.
Mechanical mounting
Fit the transducer EN20M through the hollow shaft on the drive shaft, paying attention that the fixing lock-pin
get into the Ø6 bore. For this purpose get ready the bore for the lock-pin (bore 6,1 depth 6mm) with
wheelbase 30mm from the drive shaft. Use the two threaded bores M3x10 on the back of the instruments to
fix the transducer. Then tighten the M5 screws on the hollow shaft.
Programming
To step into the parameter programming press key PGM fino a che apparirà sul display la scritta
press 2 times key RESET
increase) and
(digit selection), set out password 0273 and confirm with RESET
wrong set-out of password it goes out of the programming.
The parameters that have to be set can be run with key
value to be displayed for every turn of the shaft,
number of decimal digits,
count direction,
keys opening mode
displacement of origin,
not used.
To enter into the modification of the selected parameter press two times
value) and with keys
To go out of the programming press
Value to be displayed for one turn of transducer shaft
This parameter together with the following allows the programming of the value on the display for one turn of
transducer shaft. The Factory value is
setting of decimal point position that is, after programming of the last digit on the left, pressing key
blink the decimal pinpoint and with key
Data:13/01/16
/
and appear 4 zeroes, the first on the right is blinking, with keys
ENTER
and
set the wanted value to be confirmed with
.
=100.0. The range allowed is from 0,000001 to 9999999 with
VISUAL
it can be moved to the wanted position. Confirm with
file: F20K+EN20M_ing.doc
F20K-EN20M
and in order of appearance they are:
(one time displays only the
RESET
.
RESET
, now
(digit
/
. . In case of
ENTER
will
/
.
RESET
ENTER
pg 3/7