Digimerge DCB54DL Manual de inicio rápido - Página 2
Navegue en línea o descargue pdf Manual de inicio rápido para Cámara IP Digimerge DCB54DL. Digimerge DCB54DL 2 páginas. 700+ tvl varifocal ir bullet camera
Imprimir páginaInstalling the Camera
ATTENTION
- Test the camera prior to selecting a permanent
mounting location by temporarily connecting the camera(s) and
cables to the DVR or Observation System.
1. Use the included mounting template to
mark mounting points.
2. Loosen the fastening screw at camera base
using the small allen key.
Adjustment ring
Fastening screw
Camera base
3. Rotate the camera base counter clockwise
to separate it from the camera stand.
4. Mount the camera base to the wall using
the included screws.
NOTE: This camera is not intended for ceiling
mounting. If you mount the camera to a ceiling, the
camera will have to point downwards for adequate
clearance.
5. Loosen the camera
stand screws using
the large allen key.
6. Feed the BNC /
power termination
Camera Stand Screws
cable through the
camera base. Connect video and power
cable as described in next section 'Setting
up the Camera'.
7. Screw the camera clockwise onto the
camera base. Do not tighten all the way.
8. Move the camera to the desired position,
and while holding it firmly in place, turn
the adjustment ring on the camera stand
clockwise to tighten. Next, tighten the two
screws on the camera stand.
Setting up the Camera
1. Connect the BNC connector of the camera to
the video cable.
2. DC Power—Power Adapter: Connect a
12V DC Power Adapter (not included) to the
camera. Plug the Power Adapter into a local
power outlet.
• DC Power—Power Pigtail (not included):
Connect a Power Pigtail to the camera.
Connect the terminating wires of the cable
directly to the DC power source.
NOTE: The Power Pigtail is a non-polarity input. You
can connect the wires to either the positive or negative
ports of the DC power source.
• AC Power—Connect a Power Pigtail
(not included) to the camera. Connect the
terminating wires of the cable directly to the
24V AC power source.
3. Adjust the ZOOM and FOCUS knobs as
required.
ZOOM
FOCUS
NOTE: If the ZOOM and FOCUS knobs are too tight for
adjustment, use a philips screw driver to slightly loosen
the screws on the knobs.
Screw
Camera Specifications
Image Sensor
1/3" Sony EX-View™ II 960H
Video Format
NTSC
Effective Pixels
H: 976 V: 494
Horizontal Resolution
700+ TVL
Scan System
2:1 Interlace
Sync System
Internal
S / N Ratio
>50dB (AGC Off)
Iris
AES
AES Shutter Speed
1/60 ~ 1/100,000 sec.
Min. Illumination
0.15 LUX @ F2.0 (IR Off)
0 LUX (IR LEDs ON)
Video Output
Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type
2.8–12mm F1.4 / Varifocal
FOV (Diagonal)
28–93°
Termination
Video: BNC Female
IR Range / Qty.
110ft / 34m; 30 LED's
Power Requirement
12V DC ± 10% / 24V AC ± 10%
Power Consumption
12V: 600mA max / 24V: 400 mA max
Operating Temp. Range
–4° ~ 122°F
Environmental Rating
IP66
Dimensions (LxWxH)
10.1" x 5.4" x 3.4"
255mm x 137mm x 85mm
Weight (including stand)
1.9lbs / 0.9kg
Dimensions
255mm / 10.1"
85mm
3.4"
137mm / 5.4"