FIBARO FGBHMS-001 Manual de instrucciones - Página 5
Navegue en línea o descargue pdf Manual de instrucciones para Sensores de seguridad FIBARO FGBHMS-001. FIBARO FGBHMS-001 7 páginas. Motion sensor.
motion, light & temperature sensor
También para FIBARO FGBHMS-001: Manual de instrucciones (14 páginas), Manual rápido (18 páginas)
Imprimir página
8
#6: Functionality
Motion detection:
i
NOTE
the Motion Sensor detects movement using PiR sensor and reports it
use app that allows to
to your ioS device.
configure parameters
to adjust sensitivity,
Blink of LeD indicates detected motion. Color of blink is dependent on
sustain time and LeD
current ambient temperature (smooth transition through blue, green
indication for motion
and red). Brightness of blink is adjusted by measured light intensity.
detection.
Tamper detection:
i
NOTE
the Motion Sensor detects tampering when accessory is moved and
reports it to your ioS device. tampering is indicated with an alternate
use app that allows to
blinking in red, blue and white.
configure parameters
to adjust sensitivity
and indications for
Temperature measuring:
tamper detection.
the Motion Sensor measures ambient temperature every 5 min-
utes. if the measured temperature differs from previously reported
i
by at least 2°C (3.6°F), accessory reports it to your ioS device.
NOTE
the accessory mea-
Battery level measuring:
sures temperature in
the place of installa-
the Motion Sensor measures battery level every 24 hours and reports
tion. Remember that
it to your ioS device. additionally, if battery level is below 15%, the
temperature
near
accessory will report low level battery status to your ioS device.
the ceiling may differ
from that on eye-level
Light intensity measuring:
or the floor.
the Motion Sensor measures light intensity. if the measured light in-
tensity differs from previously reported by at least 200 lux, accessory
i
NOTE
reports it to your ioS device.
the accessory mea-
sures light intensity
PIR sensor malfunction detection (Fault Code 1):
in the place of instal-
the Motion Sensor detects malfunction of PiR sensor (responsible for
lation, not where the
sensor is pointed.
motion detection) and reports it to your ioS device.
Getting Fault Code 1 warning means that the accessory is damaged
and should be returned to the distributor for the warranty (if still valid).
FunCtionaLitY
#7: Configurable parameters
1. Motion detection – sensor sensitivity
this parameter allows to set sensitivity of PiR sensor used for motion
detection.
the higher the value of this parameter, the higher the sensitivity.
available settings: 1 – low sensitivity
2 – medium sensitivity
3 – high sensitivity
Default setting:
2 (medium sensitivity)
2. Tamper – sensor sensitivity
this parameter allows to set sensitivity of tamper detection.
the higher the value of this parameter, the higher the sensitivity.
available settings: 0 – tamper disabled
1 – low sensitivity
2 – medium sensitivity
3 – high sensitivity
2 (medium sensitivity)
Default setting:
3. Motion detection – LED indication
this parameter allows to choose how the LeD indicator will behave
after detecting motion.
available settings: 0 – LeD indications disabled
1 – color dependent on temperature*
2 – flashlight mode**
3 – white, 4 – red, 5 – green, 6 – blue, 7 – yellow,
8 – cyan, 9 – magenta
Default setting:
1 (color dependent on temperature)
4. Tamper – LED indication
this parameter allows to choose if accessory will indicate tampering
using LeD (alternate blinking in red, blue and white).
available settings: 0 – tamper indication disabled
1 – tamper indication enabled
Default setting:
1 (tamper indication enabled)
9
i
NOTE
* Color is a smooth
transition from blue
through
green
to
red in range 18-30°C
(64.4-86°F).
** in flashlight mode
the
LeD
provides
white light with high-
er brightness.
ConFiGuRaBLe PaRaMeteRS