FIBARO FGMS-001 Manual de instrucciones - Página 2
Navegue en línea o descargue pdf Manual de instrucciones para Sensores de seguridad FIBARO FGMS-001. FIBARO FGMS-001 2 páginas. Motion sensor
También para FIBARO FGMS-001: Manual de instrucciones (20 páginas), Manual de instrucciones (11 páginas)
Imprimir página
2 - only the BASIC OFF command frame sent in Basic CommandC-
XV. ADVANCED CONFIGURATION
lass.
Values of BASIC ON and BASIC OFF command frames may be
modified by dedicated parameters.
WAKE UP INTERVAL
Default setting: 0
At each wake up the Fibaro Motion Sensor communicates with the
Parameter size: 1 [byte]
main controller, updates parameter settings and the software if
necessary. The Motion Sensor will wake up at a defined time interval
and will ALWAYS try to communicate with the main controller
14. BASIC ON command frame value
Wake Up Interval set to 0 cancels the WAKE UP command frame,
The value of 255 allows to turn ON a device. In case of the Dimmer,
i.e. the device will have to be woke up manually, through the B
the value of 255 means turning ON at the last memorized state, e.g.
button, sending NODE INFO command frame.
the Dimmer turned ON at 30% and turned OFF using the value of
255, and then turned OFF, will be turned ON at 30%, i.e. the last
Available settings: 0-65535 (0-65535 seconds).
memorized state.
Default setting: 7200 (7200 seconds).
Available settings: 0 - 255
Parameter size: 2 [bytes]
Default setting: 255
Parameter size: 1 [byte]
NOTE
!
It's not recommended to set the value of Wake Up
interval below 10 seconds. Short wake up interval
16. BASIC OFF command frame value
may shorten the battery life and delay the reports or
The command frame sent at the moment of motion alarm
even make them impossible.
cancellation, after the cancellation delay time, specified in parameter
6, has passed.
The value of 0 allows to turn a device OFF while the value of 255
allows to turn ON a device. In case of the Dimmer, the value of 255
1. MOTION SENSOR'S SENSITIVITY
means turning ON at the last memorized state, e.g. the Dimmer
The lower the value, the more sensitive the PIR sensor.
turned ON at 30% and turned OFF using the value of 255, and then
Available settings: 8 - 255
turned OFF, will be turned ON at 30%, i.e. the last memorized state.
Default setting: 10
Available settings: 0 - 255
Parameter size: 1 [byte]
Default setting: 0
Parameter size: 1 [byte]
2. MOTION SENSOR'S BLIND TIME (INSENSITIVITY)
Period of time through which the PIR sensor is "blind" (insensitive) to
20. TAMPER SENSITIVITY
motion. After this time period the PIR sensor will be again able to
The parameter determines the chages in forces acting on the Fibaro
detect motion. The longer the insensitivity period, the longer the
Motion Sensor resulting in tamper alarm beig reported - g-force
battery life. If the sensor is required to detect motion quickly, the time
acceleration.
period may be shortened. The time of insensitivity should be shorter
Available settigs: 0 - 122 (0.08 - 2g; multiply by 0.016g; 0 = tamper
that the time period set in parameter 6.
inactive)
Available settings: 0 - 15
Default setting: 15 (0.224g)
Formula to calculate the time: time [s] = 0.5 x (value + 1)
Parameter size: 1 [byte]
Default setting: 15 (8 seconds)
Parameter size: 1 [byte]
22. TAMPER ALARM CANCELLATION DELAY
Time period after which a tamper alarm will be cacelled. Another
3. PIR sensor's "PULSE COUNTER"
tampering detected durig the countdown to cancellation will not
Sets the number of moves required for the PIR sensor to report
extend the delay.
motion. The lower the value, the less sensitive the PIR sensor. It's
Available settings: 1 - 65535
not recommended to modify this parameter settings.
Default setting: 30 (seconds)
Available settings: 0 - 3
Parameter size: 2 [bytes]
Formula to calculate the number of pulses: pulses = (value + 1)
Default setting: 1 (2 pulses)
Parameter size: 1 [byte]
24. TAMPER OPERATING MODES
The parameter determines the behaviour of tamper and how it
reports.
4. PIR sensor's "WINDOW TIME"
0 – Tamper alarm is reported in Sensor Alarm command class /
Period of time during which the number of moves set in parameter 3
Cancellation is not reported.
must be detected in order for the PIR sensor to report motion. The
1 – Tamper alarm is reported in Sensor Alarm command class /
higher the value, the more sensitive the PIR sensor. It's not
Cancellation is reported in Sensor Alarm commad class after the
recommended to modify this parameter setting.
time period set in parameter 22 (Tamper Alarm Cancellation Delay)
Available settings: 0 - 3
2 - Tamper alarm is reported in Sensor Alarm command class /
Formula to calculate the time: time [s] = 4 x (value + 1)
Cancellation is not reported.
Default setting: 2 (12 seconds)
Sensor's orientation in space is reported in Fibar Commad Class
Parameter size: 1 [byte]
after the time period set in paramer 22.
3 - Tamper alarm is reported in Sensor Alarm command class /
Cancellation is reported in Sensor Alarm commad class after the
time period set in parameter 22. Sensor's orientation in space is
6. MOTION ALARM CANCELLATION DELAY
reported in Fibar Commad Class after the time period set in paramer
Motion alarm will be cancelled in the main controller and the
22.
associated devices after the period of time set in this parameter. Any
4 - The maximum level of vibrations recorded in the time period set
motion detected during the cancellation delay time countdown will
in parameter 22 is reported. Reports stop being sent when the
result in the countdown being restarted. In case of small values,
vibrations cease. The reports are sent in Sensor Alarm command
below 10 seconds, the value of parameter 2 must be modified (PIR
class. Value displayed in the "value" field (0 - 100) depends on the
sensor's "Blind Time").
vibrations force. Reports to the association groups are sent using
Available settings: 1 - 65535
Sensor Alarm command class.
Default setting: 30 (30 seconds)
Available settings: 0 - 4
Parameter size: 2 [bytes]
Default setting: 0
Parameter size: 1 [byte]
8. PIR SENSOR OPERATING MODE
The parameter determines the part of day in which the PIR sensor
will be active. This parameter influences only the motion reports and
26. TAMPER ALARM BROADCAST MODE
associations. Tamper, light intensity and temperature measurements
The parameter determines whether the tamper alarm frame will or
will be still active, regardless of this parameter settings.
will not be sent in broadcast mode. Alarm frames sent in broadcast
0 - PIR sensor always active
mode may be received by all of the devices within communication
1 - PIR sensor active during the day only
range (if they accept such frames).
2 - PIR sensor active during the night only.
0 - Tamper alarm is not sent in broadcast mode.
Default setting: 0
1 - Tamper alarm sent in broadcast mode.
Parameter size: 1 [byte]
Default setting: 0
Parameter size: 1 [byte]
9. NIGHT / DAY
The parameter defines the difference between night and day, in
40. ILLUMINATION REPORT THRESHOLD
terms of light intensity, used in parameter 8.
The parameter determines the change in light intensity level
Available settings: 1 - 65535
resulting in illumination report being sent to the main controller.
Default setting: 200 (200 lux)
Available settings: 0 - 65535 (1 - 65535 lux; 0 = reports are not
Parameter size: 2 [bytes]
sent)
Default setting: 200 (200 lux)
Parameter size: 2 [byte]
12. BASIC COMMAND CLASS FRAMES CONFIGURATION
The parameter determines the command frames sent in 1-st
association group, assigned to PIR sensor.
42. ILLUMINATION REPORTS INTERVAL
0 - BASIC ON and BASIC OFF command frames sent in Basic
Time interval between consecutive illumination reports. The reports
Command Class.
are sent even if there are no changes in the light intensity.
1 - only the BASIC ON command frame sent in Basic Command
Available settings: 0 - 65535 (1 - 65535 seconds; 0 = reports are
Class.
not sent)
Default setting: 0 (no reports)
82. AMBIENT ILLUMINATION LEVEL BELOW WHICH LED
Parameter size: 2 [bytes]
BRIGHTNESS IS SET TO 1%
The parameter is relevant only when the parameter 81 is set to 0.
Available settings: 0 to parameter 83 value
Default setting: 100 (100 lux)
NOTE
!
Parameter size: 2 [bytes]
Frequent reports will shorten the battery life.
Parameter value under 5 may result in blocking the
temperature reports.
83. AMBIENT ILLUMINATION LEVEL ABOVE WHICH LED
BRIGHTNESS IS SET TO 100%
60. TEMPERATURE REPORT THRESHOLD
The parameter is relevant only when the parameter 81 is set to 0.
The parameter determines the change in level of temperature
Available settings: parameter 82 value to 65535
resulting in temperature report being sent to the main controller.
Default setting: 1 000 (1 000 lux)
Available settings: 0 - 255 (0.1 - 25.5oC; 0 = reports are not sent)
Parameter size: 2 [bytes]
Default setting: 10 (1oC)
Parameter size: 1 [byte]
!
62. INTERVAL OF TEMPERATURE MEASURING
The parameter determines how often the temperature will be
measured. The shorter the time, the more frequently the temperature
will be measured, but the battery life will shorten.
Available settings: 0 - 65535 (1 - 65535 seconds; 0 = temperature
86. MINIMUM TEMPERATURE RESULTING IN BLUE LED
will not be measured)
Default setting: 900 (900 seconds)
ILLUMINATION
This parameter is relevant only when parameter 80 has been
Parameter size: 2 [bytes]
properly configured.
Available settings: 0 to parameter 87 value (degrees celsius)
Default setting: 18 (18oC)
NOTE
!
Parameter size: 1 [byte]
Frequent reports will shorten the battery life.
Parameter value under 5 may result in blocking the
ilumination reports.
87. MAXIMUM TEMPERATURE RESULTING IN RED LED
ILLUMINATION
This parameter is relevant only when parameter 80 has been
64. TEMPERATURE REPORTS INTERVAL
properly configured.
The parameter determines how often the temperature reports will be
sent to the main controller.
Available settings: parameter 86 value to 255 (degrees celsius)
Default setting: 28 (28oC)
Available settings: 0 - 65535 (1 - 65535 sekund; 0 = reports are not
Parameter size: 1 [byte]
sent)
Default setting: 0
Parameter size: 2 [byte]
89. LED INDICATING TAMPER ALARM
Indicating mode resembles a police car (white, red and blue).
0 - LED does not indicate tamper alarm.
66. TEMPERATURE OFFSET
1 - LED indicates tamper alarm.
The value to be added to the actual temperature, measured by the
sensor (temperature compensation).
Default setting: 1
Parameter size: 1 [byte]
Available settings: 0 - 100 (0 to 100oC) or 64536 - 65535 (-100 to
-0.10oC)
Default setting: 0
Parameter size: 2 [bytes]
XVI. GUARANTEE
80. LED SIGNALING MODE
1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.
(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1;
The parameter determines the way in which LED diode behaves
after motion has been detected.
60-421 Poznan, entered in the register of the National
Values from 1 to 9 = single long blink at the moment of reporting
Register kept by the District Court in Poznań, VIII Economic
Department of the National Court Register, no. 370151, NIP
motion. No other motion will be indicated until alarm is cancelled.
7811858097, REGON: 301595664.
Values from 10 to 18 = single long blink at the moment of reporting
2. The Manufacturer is responsible for equipment malfunction
motion and one short blink each time the motion is detected again.
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
Values from 19 to 26 = single long blink at the moment of reporting
3. During the Guarantee period, the Manufacturer shall remove any
motion and two short blinks each time the motion is detected again.
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
0. LED inactive.
Device with new or regenerated components, that are free of
1. LED colour depends on the temperature. Set by parameters 86
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which
and 87.
2. Flashlight mode - LED glows in white for 10 seconds.
shall be free of any defects and its condition shall not be worse than
3. White.
the original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
4. Red.
5. Green.
device of the same type (e.g. the device is no longer available in the
6. Blue.
commercial offer), the Manufacturer may replace it with a different
7. Yellow.
device having technical parameters similar to the faulty one. Such
8. Cyan.
activity shall be considered as fulfilling the obligations of the
9. Magenta.
Manufacturer. The Manufacturer shall not refund money paid for the
10. LED colour depends on the temperature. Set by parameters
device.
5. The holder of a valid guarantee shall submit a guarantee claim
86 and 87.
11. Flashlight mode - LED glows in white through 10 seconds.
through the guarantee service. Remember: before you submit a gu-
Each next detected motion extends the glowing by next 10
arantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved remotely,
seconds.
12. White.
saving time and money spent to initiating guarantee procedure. If
13. Red.
remote support is insufficient, the Customer shall fill the guarantee
14. Green.
claim form (using our website - www.fibargroup.com) in order to
15. Blue.
obtain claim authorization. When the guarantee claim form is sub-
16. Yellow.
mitted correctly, the Customer shall receive the claim confirmation
17. Cyan
with an unique number (Return Merchandise Authorization -RMA).
18. Magenta
6. The claim may be also submitted by telephone. In this case, the
19. LED colour depends on the temperature. Set by parameters
call is recorded and the Customer shall be informed about it by a
86 and 87.
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
20. White
21. Red
number (RMA-number).
22. Green
7. When the guarantee claim form is submitted correctly, a
23. Blue
representative of the Authorised Guarantee Service (hereinafter as
24. Yellow
"AGS") shall contact the Customer.
25. Cyan
8. Defects revealed within the guarantee period shall be removed
26. Magenta
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Default setting: 10
Device was kept by AGS.
Parameter size: 1 [byte]
9. The faulty device shall be provided by the Customer with complete
standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
81. LED BRIGHTNESS
process shall be equal to the guarantee period of the original device.
The parameter determines the brightness of LED when indicating
The guarantee period of the replaced part shall not be extended.
motion.
11. Costs of delivering the faulty device shall be borne by the
Available settings: 0 - 100 (1 - 100%; 0 = brightness determined by
Customer. For unjustified service calls, the Service may charge the
the ambient lighting - see parameters 82 and 83)
Customer with travel expenses and handling costs related to the
Default setting: 50
case.
Parameter size: 1 [byte]
12. AGS shall not accept a complaint claim only when:
12. AGS shall not accept a complaint claim only when:
• the Device was misused or the manual was not observed,
• the Device was provided by the Customer incomplete, without
accessories or
nameplate,
• it was determined that the fault was caused by other reasons than
a material or
manufacturing defect of the Device
• the guarantee document is not valid or there is no proof of
purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
14. The guarantee shall not cover:
• mechanical damages (cracks, fractures, cuts, abrasions, physical
NOTE
deformations caused by impact, falling or dropping the device or
The value of the parameter 83 must be higher than
other object, improper use or not observing the operating manual);
the value of the parameter 82.
• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;
• damages caused by malfunctioning software, attack of a computer
virus, or by failure to update the software as recommended by the
Manufacturer;
• damages resulting from: surges in the power and/or telecommuni-
cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
• damages caused by using accessories not recommended by the
Manufacturer
• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;
• damages caused by Customer's failure to provide maintenance
and servicing activities defined in the operating manual;
• damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
• defects caused by operating faulty Device or accessories.
15. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
Court
agreement.
This Device may be used with all devices
i
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.
Any device compatible with Z-Wave may be
added to Fibaro system.
FIBAR GROUP
FIBARO
In case of any technical questions contact customer service centre in
your country.
www.fibaro.com