Sharp 32BC2K Manual de inicio rápido - Página 2
Navegue en línea o descargue pdf Manual de inicio rápido para TV LCD Sharp 32BC2K. Sharp 32BC2K 2 páginas.
También para Sharp 32BC2K: Instrucciones de uso Inicio rápido Manual de configuración (2 páginas)
Imprimir página
Setting up the TV set for the fi rst time
1
Fitting the stand
TV panel must be facing downwards.
For the stand installation, there is
one type of screw provided as shown
below.
To complete the stand installation you
will require a cross head screw driver.
Place the TV set on a fl at and
1
clean surface with the panel facing
downwards to avoid damage.
Place the TV set on a fl at and clean surface
with the panel facing downwards to avoid
4 x
damage.
Used for attaching the stand
to the TV set (fi g.2)
Connecting your set
2
1) Connect the TV to your power socket.
2) If you wish to use the TV to receive Freeview/Saorview channels, connect the RF input
from the TV to your outdoor Digital TV aerial. If you do not wish to receive Freeview/
Saorview, skip this step.
4 First time installation
Basic installation steps are shown below. These may vary slightly depending on model.
1
Introduction
When the set fi rst turns on, it enters the First Time Installation
mode. This can be restarted by restoring the set to default settings
in the 'About TV' Menu.
Note: In home mode,
the TV will switch off
automatically after 4
hours in the event that
no buttons are pressed on
the TV or remote control.
(You can change this
by pressing the [MENU]
button and then selecting
Settings>Time>Auto
4
Standby)
Environment of Use
Home Mode: For normal use, by default it is set to a power saving mode
which reduces the energy used by up to 25% (by reducing the power to
the LED/LCD panel). This can be changed in the picture mode settings.
7
Default Source
Select the source which you use the most. If Digital TV (Freeview) is chosen,
then at the next step, the set will tune in and default to Digital TV (Freeview).
If one of the other sources is selected, then the set will not tune in at this
stage and default to that input. If it is required to tune the set in later, press
the [MENU] button and then select Settings>Channels
To obtain a copy of your Operating Instructions, please go to: www.umc-uk.co.uk/instruction-manuals/sharp
Back/Shortest
R
Front/Longest
L
2
When the stand feet are installed correctly the
stand feet will be longest at the front of the TV
and shortest at the back with the feet pointing
away from each other.
3 Powering On the TV
TV Control Stick
TV control stick
Switch on the television by pressing
the TV control stick located on the
TV set.
2
Languages
Select your preferred on-screen display language. This will change the language
in which the menus and associated information is displayed in. When set up has
been completed, to change this press the [MENU] button and then select Settings >
System Menu > Language
5
Network setup
You can connect the TV to your broadband router or wireless network in order
to take advantage of the Smart functions. If you connect the TV to your router
using an Ethernet cable (recommended) this step will be skipped.
8
Tune in Channels
Choose to install terrestrial channels now or later.
3
4
1
2
4 x
3
When the stand/feet are in the correct
position, secure the feet to the underside of
the TV set using 4 screws provided.
Remote Control: Installing Batteries
Insert the batteries supplied into the remote
control and press the standby button to power
on the TV.
3
Country Selection
Select the correct fl ag for the country in which the set will be
used in. This will enable the set to correctly install the functions
applicable in the country of use.
6
Set Up Netfl ix
If you have a Netfl ix account, it can be set up on the television
here. Once set up and validated, the First Time Installation
returns to the next step.
9
Support Advice
Information regarding support is displayed for a little while.
Tuning continues and a progress bar is shown with the number of
channels found indicated below.
If you are picking up signals from more than one transmitter, you
will be requested to select your primary and secondary regions.
Wall Mounting the TV
1. Remove the four screws that are supplied
in the wall mounting holes.
2. The wall mount can now be easily
attached to the mounting holes on
the rear of the TV.
3. Install the wall mounting bracket to the
television as advised by the bracket
manufacturer.
The picture shows the use of spacers, which
are not applicable to all sets/installations.
Image for illustration only.
Connectivity
SCART
G
1
2
C
D
DIGITAL
ETHERNET
AUDIO OUT
OPTICAL
L
R
VIDEO/Y
Pb
Pr
A
B
E
F
H
A
Ethernet/LAN*
Network connection
SAT In
B
I
Digital Audio
Digital Optical Audio Output
RF in
J
C
HDMI 1
HDMI input
HDMI 3
D
HDMI 2
HDMI input (ARC)
K
Earphones
Audio shared for Video/Composite
E
L
L/R
HDMI input (ARC)
Service Input
and component/ YPbPr
Video Input (green) and HD input
F
M
Video/YPbPr
HD input (YPbPr)
CI card in
(Ypbpr)
G
N
SCART
SCART input
USB 2.0
* The Ethernet/LAN port is used for Freeview HD services and smart functions.
Satellite Input
RF / TV aerial input
HDMI input
Earphone input
Input is used only by service centres
Common interface module
USB port 2.0