Sharp AR-M208 Manual de servicio - Página 15
Navegue en línea o descargue pdf Manual de servicio para Impresora todo en uno Sharp AR-M208. Sharp AR-M208 32 páginas. Digital laser copier/ printer
También para Sharp AR-M208: Manual del Operador de Llaves (24 páginas)
Imprimir página[8] SIMULATION
2. Simulation code list
Code
Main
Sub
3
3
Used to check the operation of the load in the
finisher and the control circuit.
8
1
Used to check and adjust the operation of the
developing bias voltage in each copy mode and
the control circuit.
2
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each copy
mode and the control circuit.
3
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each copy
mode and the control circuit.
10
Used to check and adjust the operation of the
developing bias voltage in each printer mode and
the control circuit.
11
Used to check and adjust the operation of the main
charger grid voltage (high mode) in each printer
mode and the control circuit.
12
Used to check and adjust the operation of the main
charger grid voltage (low mode) in each printer
mode and the control circuit.
9
1
Used to check and adjust the operation of the load
(motor) in the duplex section and the control
circuit.
5
Used to adjust the switch back time of the duplex
motor.
21
1
Used to set the maintenance cycle.
22
3
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
5
Used to check the ROM version of each unit
(section).
10
Used to check the system configuration.
12
Used to check the misfeed positions and the
number of misfeed at each position. (When the
number of misfeed is considerably great, it can be
judged as necessary for repair.)
24
15
Used to clear the scanner mode counter.
25
1
Used to check the operation of the main drive
(excluding the scanner section) and to check the
operation of the toner concentration sensor. (The
toner concentration sensor output can be
monitored.)
26
6
Used to set the specifications depending on the
destination.
12
Used to input the Software Key for E-MAIL RIC.
14
Used to input the Software Key for the PS
extension kit.
22
Used to set the specification (language display) for
the destination.
41
Used to set whether the automatic magnification
ratio select (AMS) is always ON or not when
setting the pamphlet (center binding) function.
57
Used to set the model code.
43
1
Used to set the fusing temperature in each
operation mode.
44
34
Used to adjust the transfer current value.
46
2
Used to adjust the copy exposure level.
18
Used to adjust the copy contrast. (Inclination)
19
Used to change the image quality in the exposure
mode.
20
Used to correct SPF exposure.
Function
AR-M208 SIMULATION 8 - 1
Code
Main
Sub
50
1
Used to adjust the copy lead edge position.
5
Used to adjust the print image position (top
margin) on the print paper in the print mode.
6
Used to adjust the print image position (top
margin) on print paper in the copy mode. (SPF/
RSPF)
10
Used to adjust the print image center position.
(Adjustment can be made for each paper feed
section.)
51
1
Used to adjust the OPC drum separation pawl ON
time.
2
Used to adjust the contact pressure of paper onto
the resist roller in each section (copier paper feed
section, duplex paper feed section, SPF paper
feed section). (When the print image position
varies greatly for the paper or when a lot of paper
jam troubles occur, the adjustment is required.)
9
Used to adjust ON/OFF timing of the separation
voltage.
53
8
Used to adjust the mirror unit SPF scan position
automatically.
For the SPF scan position auto adjustment, the
mirror unit is shifted to 11mm before the SPF glass
cover edge and is moved by self-boost, and
images are scanned in each step, and the position
from the glass cover edge is automatically
detected.
[Adjustment value]
Default: 50
Adjustment unit 1 = about 0.127mm
64
1
Self print
Key input = 1
Self print is performed in the 2-by-4 mode (2-line
print and 4-line non-print).
Key input = 2
Grid print is performed. (1cm, 1-dot width WLT/A3
print (A3 main scan, WLT sub scan))
67
11
Used to set the Select-IN signal.
14
Used to check write/comparison of flash programs.
17
Used to clear NVRAM.
18
Used to clear the data area for FLASH ROM
Network Scanner Application.
20
Used to check the network connection when a
scanner option is installed.
3. Details
3
3-3
Purpose
Operation test/check
Function
Used to check the operation of the load in the finisher
(Purpose)
and the control circuit.
Section
Sorter/Finisher
Item
Operation
Operation/procedure
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
Function
Setting range: 1 to 99