MPC3-302
3-Series® Media Presentation Controller 302
The Crestron® MPC3-302 is a wall-mounted, PoE+ (Power over Ethernet Plus) powered
3-Series® automated processor and control panel all in one. The MPC3-302 offers
fully-programmable functionality, supports configuration and management via web or
cloud-based interfaces, and integrates with Crestron Fusion® software as part of a complete
managed enterprise solution.
NOTE:
The MPC3-302 can be installed onto a tabletop or other flat surface using the
TTK-MP/MPC/IPAC tabletop kit and the optional SMK-MP/MPC/IPAC swivel mount kit. For
more information and installation instructions, refer to the TTK/MP/MPC/IPAC &
SMK-MP/MPC/IPAC Installation Guide (Doc. 6782) at www.crestron.com/manuals.
Check the Box
Item
MPC3-302-B or MPC3-302-W
Bit, Torx®, T8, Security (P/N 2025915)
Key (P/N 2052297)
Plate, Metal, Mounting, 6.5 in. x 4.3 in. x 1.5 in. (P/N 2049785)
Screw, 4-20 x 3/4 in., Pan Head, Phillips, Thread Forming (P/N 2007140)
Screw, 4-40 x 1/4 in., Pan Head, Phillips (P/N 2007156)
Screw, 6-32 x 1 in., Pan Head, Phillips (P/N 2007251)
Screw, Security, Torx® (P/N 2051148)
MPC3-302-B Only
Button Cap, Black (P/N 2049780)
Button Cap, Mute, Black (P/N 2049784)
Button Cap, Power, Black (P/N 2049782)
Cover, Black (P/N 4527101)
Labels, Sources, 30 Piece Set, Black (P/N 4527386)
MPC3-302-W Only
Button Cap, White (P/N 2049779)
Button Cap, Mute, White (P/N 4527719)
Button Cap, Power, White (P/N 4527718)
Cover, White (P/N 4527100)
Labels, Sources, 30 Piece Set, White (P/N 4527385)
Attach the Mounting Plate
The MPC3-302 is designed to install into a 3-gang U.S. electrical box.
•
Use the four 6-32 x 1 in. screws to attach the MPC3-302 mounting plate to the electrical
box with the "TOP" label properly oriented.
•
Ensure that the mounting plate is level and flush against the electrical box after
installation.
Drywall
surface
Qty
1
1
1
1
Mounting
6
plate
6
4
1
Screw (4):
6-32 x 1 in.
10
1
1
1
Connect the Device
1
Route all necessary cables through the rear of the electrical box, and then make connections to
the MPC3-302 as shown in the following illustration.
10
NOTE:
Make all cable connections prior to attaching the MPC3-302 assembly to the electrical
box.
1
NET:
1
To any Cresnet
1
network device
1
LAN PoE
I/O
RELAY:
To controllable
devices
IR:
COM:
To IRP2 emitter
To any
or serial devices
RS-232 device
Observe the following when making connections to the MPC3-302:
•
•
•
•
3-gang U.S.
electrical box
•
To install the MPC3-302:
1.
LAN PoE:
100BASE-TX
Ethernet to LAN
NOTE:
TTK-MP/MPC/IPAC enclosure. For more information, refer to the TTK/MP/MPC/IPAC &
SMK-MP/MPC/IPAC Installation Guide (Doc. 6782).
I/O:
Ground
To digital or
analog devices
Use Crestron power supplies for Crestron equipment.
A single Ethernet cable provides power to the MPC3-302. A PoE+ power supply or a
network switch capable of PoE+ is recommended (both sold separately).
The MPC3-302 must use PoE+ to supply power to a Cresnet® network device via the NET
connector.
Ensure that the device is properly grounded by connecting the chassis ground lug to a
known earth ground (such as building steel).
Apply power to the MPC3-302 after all connections have been made.
Install the Device
Once all cable connections have been made, use the six 4-40 x 1/4 in. screws to attach the
MPC3-302 assembly to the mounting plate.
Mounting
plate
Screw (6):
MPC3-302
4-40 x 1/4 in.
assembly
The six included 4-20 x 3/4 in. screws are used to attach the MPC3-302 assembly to the
Imprimir página