Siemens CD634GA 0 Series Manual del usuario e instrucciones de instalación - Página 9
Navegue en línea o descargue pdf Manual del usuario e instrucciones de instalación para Horno Siemens CD634GA 0 Series. Siemens CD634GA 0 Series 36 páginas.
También para Siemens CD634GA 0 Series: Manual de instrucciones (32 páginas)
Imprimir página
6.2 Initial configuration
When the appliance is connected to the power supply
for the first time or following a lengthy power failure, the
settings that you will need to configure before you can
use it will appear.
Note: You can change these settings at any time by
going to the basic settings.
→ "Basic operation", Page 9
Setting the language
Use the rotary selector to select the required lan-
1.
guage.
Press .
2.
a The next setting will appear.
Note: You can change these settings at any time by
going to the basic settings.
→ "Basic operation", Page 9
Setting the time
1.
Use the rotary selector to set the current time.
Press .
2.
a The next setting will appear.
Setting the date
Use the rotary selector to set the current date.
1.
Press .
2.
a The next setting will appear.
Setting the water hardness
Use the rotary selector to set the water hardness
1.
range.
Press .
2.
a This saves the water hardness range.
a A message will now appear on the display confirm-
ing that initial configuration is complete.
6.3 Calibrating the appliance
The boiling point of water depends on the air pressure.
During the calibration process, the appliance adjusts to
the pressure conditions in the location where it is in-
stalled. Large amounts of steam may be generated dur-
ing the calibration process.
Running the calibration process
Notes
¡ Do not open the appliance door while calibration is
in progress as this will abort the calibration process.
7 Basic operation
7.1 Switching on the appliance
Press
to switch the appliance on.
▶
a The Siemens logo will appear on the display, fol-
lowed by the heating function selection list.
Tip: In the basic settings, you can specify which oper-
ating mode should appear when you switch on the ap-
pliance.
→ "Basic settings", Page 15
¡ If you move house, restore the appliance's basic
factory settings once it is installed so that it can ad-
apt to its new location. Repeat the procedures for
initial configuration and calibration.
¡ Your appliance will retain these calibration settings
even in the event of a power failure or disconnection
from the mains. Recalibration is not necessary.
Requirement: The cooking compartment is cold or at
room temperature.
Remove the accessories and any leftover packaging
1.
(e.g. polystyrene pellets) from the cooking compart-
ment.
Wipe the smooth surfaces in the cooking compart-
2.
ment with a soft, damp cloth.
Press
to switch on the appliance.
3.
Fill the water tank.
4.
→ "Filling the water tank", Page 10
Set the required heating function, temperature and
5.
cooking time.
→ "Setting the heating function and temperature",
Page 11
Setting
Heating function
Temperature
Cooking time
Press
to switch the appliance off.
6.
Wait until the cooking compartment has cooled
7.
down.
6.4 Cleaning the cooking compartment
Requirement: The cooking compartment is cold or at
room temperature.
Clean the smooth surfaces with soapy water and a
1.
dish cloth.
Empty and dry the water tank.
2.
Dry the cooking compartment.
3.
6.5 Cleaning the accessories
Clean the accessories with soapy water and a dish
▶
cloth or soft brush.
7.2 Switching off the appliance
Press
to switch the appliance off.
▶
a The appliance will now shut down. Any functions
currently in progress will be aborted.
a The time will appear on the display.
7.3 Starting the appliance
To start the appliance, press
▶
Basic operation en
Value
Steam
100 °C
20 minutes
.
9