Epson ActionTower 3000 Computer Manual de configuración rápida - Página 3
Navegue en línea o descargue pdf Manual de configuración rápida para Proyector Epson ActionTower 3000 Computer. Epson ActionTower 3000 Computer 4 páginas. Product information guide
También para Epson ActionTower 3000 Computer: Manual del usuario (34 páginas), Manual del usuario (38 páginas), Sustitución de cartuchos (2 páginas), Lea primero este manual (29 páginas), Manual de información del producto (11 páginas)
Imprimir página
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Turn projector on
Choose which source to
display
Switch between 2D
and 3D
Access projector menus
Control WirelessHD functions
(PowerLite Home Cinema
3600e only)
For more information on using the remote control, see the online
User's Guide.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of Epson
(part number V12H548006) or Epson-compatible RF 3D active shutter glasses
(included with PowerLite Home Cinema 3500/3510/3600e).
1
Turn on and begin playback on the 3D-compatible video device.
Note: Make sure you set the video device to play content in 3D mode.
2
Press the 3D Format button on the remote control, if necessary.
3
Slide the power switch on your 3D glasses to the On position.
Note: If the glasses don't automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
You can also automatically convert 2D HDMI content to 3D (PowerLite Home
Cinema 3500/3510/3600e). To enable the 2D-to-3D Conversion option, press
the Menu button on the projector or remote control. Select Signal and press
Enter, then select 3D Setup and press Enter. Select 2D-to-3D Conversion and
press Enter. Select the Weak, Medium, or Strong setting, then press Enter.
See the online User's Guide for more information on adjusting 3D images.
Viewing WirelessHD content
(PowerLite Home Cinema
3600e)
Turn projector off
1
2
3
4
Navigate projector
menus
5
6
®
7
See the online User's Guide for more information on adjusting and configuring
the WirelessHD connection and display modes.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
video device or computer, check the following:
•
•
•
•
Turn on your video device and begin playback.
Turn on the power switch on the side of the WirelessHD Transmitter.
Turn on the projector.
If you have connected a television or other display to the output port on
the transmitter and want to switch between wired and wireless display
modes, press the Output button on the remote control or transmitter.
The WiHD light on the transmitter will light up when the wireless display
mode is active.
Press the WirelessHD button on the remote control.
Note: If the WirelessHD connection fails, press the Setup button on
the bottom of the transmitter, then try again.
If you have connected multiple input devices to the transmitter, press
the Input button on the remote control or transmitter once to display
the sub-screen menu, then press the button again to switch between the
input devices.
To display two WirelessHD input devices simultaneously, press the P-in-P
button on the remote control to enable picture-in-picture mode. Press and
hold the P-in-P button for three seconds to switch the main image and
sub-screen, or press the P-in-P button again to disable picture-in-picture
mode.
Make sure the power light on the projector is blue and not flashing.
Press the
button on the projector or one of the Source buttons on
the remote control to switch to the correct image source, if necessary.
If you're using a Windows
laptop, press the function key on your
®
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
If you're using a Mac laptop, open System Preferences and select
Displays. Click the Arrangement tab and select the Mirror Displays
checkbox.
. You may have to hold down the