Siemens DIF4305 Instrucciones de instalación y funcionamiento

Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Lavavajillas Siemens DIF4305. Siemens DIF4305 2 páginas.

Brief and handy:
en
everything your dishwasher
needs.
Before using for the first
time, read the installation
and operating instructions!
Fill with salt
Fill with rinse aid

Fill with detergent

Turn on the tap
Water ready
Switch on the appliance
Close the door. Press the On/Off switch,
the last selected programme starts automatically.
Select programme
Off we go
Switch off the appliance
When the "programme end" display illumi-
nates, switch off the main switch. Turn off
the tap.

Setting the water softening system *

Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Dissolves limescale (not required for set value 0!)
Unscrew
the lid.
Everything is sparkling clean ...
Press mark 1,
lift up lid 2.
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Quick, economical or intensive ...
Overview of programmes
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Programme progress / Rinsing noises
Example: Eco programme
Everything o.k.
Start
Read off the setting
°fH
°dH
°Clarke mmol/l
Setting
0–6
0–11
0–8
0–1,1
0
7–16
12–29
9–20
1,2–2,9
1
17–21
30–37
21–26
3,0–3,7
2
22–35
38–60
27–44
3,8–6,2
3
Only before using
the dishwasher
for the first time
pour approx. 1 l /
2 pt water into the
salt opening.
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer's instructions.
Duration in minutes
Power consumption in kWh
Water consumption in litres
Cleaning / Final rinse
Alternating rinsing and pumping noises
After the drying cycle, water is pumped out for approx. 60 sec. The programme has not ended until the end display
Quickly sorted
and then select a setting
– Hold down programme button B and switch on the main
A
B
C
switch, then release the buttons. The
buttons A and B illuminate (water hardness setting was set
Reset
to 2 at the factory).
– Each time button B is depressed, the setting increases by
one (0-3). If buttons A, B and C illuminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Refill whenever level indicator is light!
Pour in
rinse aid.
Pour in
detergent.
Normal
Eco
Intensive
70_
65_
50_
103
140
155
1,40
1,35
0,80
20
18
13
No rinsing noises
. display flashes and
Screw on the
lid. Switch on
dishwasher
immediately.
Close the
lid. CLICK!
Push the lid
shut, press.
PLOP!
Quick
Prerinse
Gentle
40_
35_
71
30
20
0,70
0,50
0,10
14
10
4
Dry
15–35 min
m
End display
m
lights up