Cisco 1721 - VPN Security Router Bundle Manual del usuario - Página 33
Navegue en línea o descargue pdf Manual del usuario para Enrutador de red Cisco 1721 - VPN Security Router Bundle. Cisco 1721 - VPN Security Router Bundle 48 páginas. Troubleshooting guide
También para Cisco 1721 - VPN Security Router Bundle: Manual de instalación del hardware (11 páginas), Manual de inicio rápido (17 páginas), Ficha de datos (12 páginas), Solución de problemas de hardware (12 páginas)
Imprimir página
Place the seventh label on the router as shown in
Step 8
so that one half of the label covers the enclosure and the other half covers the right WAN interface card
slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Step 9
Place the eighth label on the router as shown in
so that one half of the label covers the enclosure and the other half covers the Compact Flash slot. Any
attempt to remove a CF card will leave tamper evidence.
Step 10
The labels completely cure within five minutes.
To apply tamper-evidence labels to the Cisco 3745:
Step 1
Clean the cover of any grease, dirt, or oil before applying the tamper evidence labels. Alcohol-based
cleaning pads are recommended for this purpose. The temperature of the router should be above 10°C.
Step 2
Place the first label on the router as shown in
that the one half of the tamper evidence label covers the enclosure and the other half covers the right side
of the router. Any attempt to remove the enclosure will leave tamper evidence.
Place the second label on the router as shown in
Step 3
so that the one half of the tamper evidence label covers the enclosure and the other half covers the left
side of the router. Any attempt to remove the enclosure will leave tamper evidence.
Place the third label on the router as shown in
Step 4
that the one half of the label covers the enclosure and the other half covers the top-left Network Module
slot. Any attempt to remove a network module will leave tamper evidence.
Place the fourth label on the router as shown in
Step 5
so that the half of the label covers the enclosure and the other half covers the bottom-left Network
Module slot. Any attempt to remove a network module will leave tamper evidence.
Place the fifth label on the router as shown in
Step 6
that the one half of the label covers the enclosure and the other half covers the top-right Network Module
slot. Any attempt to remove a network module will leave tamper evidence.
Step 7
Place the sixth label on the router as shown in
that the half of the label covers the enclosure and the other half covers the bottom-right Network Module
slot. Any attempt to remove a network module will leave tamper evidence.
Step 8
Place the seventh label on the router as shown in
so that one half of the label covers the enclosure and the other half covers the left WAN interface card
slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Place the eighth label on the router as shown in
Step 9
so that one half of the label covers the enclosure and the other half covers the middle WAN interface card
slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Place the ninth label on the router as shown in
Step 10
that one half of the label covers the enclosure and the other half covers the right WAN interface card slot.
Any attempt to remove a WAN interface card will leave tamper evidence.
Place the tenth label on the router as shown in
Step 11
that one half of the label covers the enclosure and the other half covers the Compact Flash slot. Any
attempt to remove a CF card will leave tamper evidence.
The labels completely cure within five minutes.
Step 12
Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, and 3745 Modular Access Routers and 7206-VXR NPE-400 Router FIPS 140-2 Non-Proprietary
OL-6083-01
The Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, 3745, and 7206 VXR NPE-400 Routers
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed so
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed so
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed so
Figure
23. The tamper evidence label should be placed so
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed
Figure
23. The tamper evidence label should be placed so
Figure
23. The tamper evidence label should be placed so
33