C2AI MVE215S-65 Manual
Navegue en línea o descargue pdf Manual para Controlador C2AI MVE215S-65. C2AI MVE215S-65 7 páginas. Globe valves actuators
Imprimir página
FORCE
MODEL
POWER SUPPLY
[N]
MVE204-65
400
MVE206-65
600
MVE210-65
1000
230Vac±10%
MVE215-65
1500
MVE222-65
2200
MVE204S-65
400
MVE206S-65
600
MVE210S-65
1000
230Vac±10%
MVE215S-65
1500
MVE222S-65
2200
APPLICATION AND USE
MVE2xx-65 is a flexible electro-mechanical actuator for the control of
two and three way globe valves in:
•
heating and cooling systems
•
Air Handling Units
•
district heating plants
•
industrial temperature control systems.
MVE2xx-65 can be controlled either by a proportional (modulating)
signal or by an increase/decrease (Floating) signal.
It is easy to mount and connect the actuator. Direct mounting is pos-
sible to any C2AI flanged valve. Linkage kits are available for C2AI
threaded valves as well as for valves of other manufac-turers (table
page 3).
The actuator has a fine resolution (500 steps on the full stroke range)
for exacting fluid control and it is able to self-calibrate on a different
stroke without the need of any user action (this function is DIP switch
selectable on the field).
MVE2xx-65 has intelligent behaviour and alarm functionality in case
of unexpected operation, feedback of alarms to the user is provided
by LEDs (GREEN and RED) on the control board.
N.B.: Do not use the actuator if not coupled with its relating valve.
MVE2xx-65 is suitable for harsh environment requiring IP65 protection
degree.
OPERATION
The actuator translates the control signal (modulating or 3 point
floating) from the controller into a valve position. A modern
brushless DC motor in the actuator drive a gear train and a worm
gear – screw
Siège social Lyon
/ 9 rue de Catalogne - Parc des Pivolles - 69153 Décines Cedex / +33 (0)4 72 15 88 70 /
Agence Île de France
DESCRIPTION
long yoke, modulating/
floating control, IP65
short yoke, modulating/
floating control, IP65
Agence Est
Agence Sud-Ouest
jack mechanism convert the motor revolutions into accurate and
repeatable linear movements.
Control Signal
MVE2xx-65 can be controlled by one of 2 main control types.
•
3 point floating;
•
modulating (or proportional) signal with field selectable range
(e.g., 0-10Vdc, 2-10Vdc, 0-5/2-6Vdc, 5-10/6-10Vdc and 4-20mA).
Manual Override
There is a manual operation handle on the actuator. When it is low-
ered (manual override ON), the power supply to the motor power
stage circuitry is cut and the motor stops. The actuator can be op-
erated manually and the valve positioned accordingly. The manual
override lever latches in position until it is raised again, then board
and motor will be powered again. At the end of this operation the
actuator moves to initial position (on the basis of DIP n. 1 setting) then
it follows the control signal. When the manual override is engaged
the GREEN and the RED LED are ON.
Manual operation handle can also be used to modify any DIP switch
setting or as re-set function after any alarm occurrence. The actua-
tor is supplied with the manual override lowered (ON).
t is not necessary to remove power supply to modify DIP switch set-
ting, but, in this case, take care of 230Vac voltage.
Feedback position
The actuator utilizes a 2-10V position feedback (look at DIP n. 1 set-
ting).
Calibration
The actuator has both auto and manual stroke calibration, DIP n. 7.
In factory delivery the auto stroke calibration is enabled – manual
calibration is not necessary unless maintenance is required on the
valve or certain alarm functions are desired.
Service Export
Globe Valves Actuators
230 Vac IP65
REF. MVE2xx65
Page 1
e
www.c2ai.com
l