3Com 3CR860-95 - OfficeConnect Secure Router Manual de instalación - Página 2
Navegue en línea o descargue pdf Manual de instalación para Enrutador de red 3Com 3CR860-95 - OfficeConnect Secure Router. 3Com 3CR860-95 - OfficeConnect Secure Router 2 páginas. Secure router
También para 3Com 3CR860-95 - OfficeConnect Secure Router: Características y ventajas (2 páginas)
Imprimir página
1
INSTALLING YOUR ROUTER
Connecting Your Router
1. Connect the power adapter to the Router and wait for the Alert
LED to stop flashing. The Alert LED may continue to flash for one
minute or longer, depending on your network configuration.
2. Ensure that your modem and computer are both switched on.
3. Use the supplied cable to connect the Router's Ethernet Cable/
DSL port to the modem. Check that the Cable/DSL Status LED lights.
4. Connect your computer to one of the 10/100 LAN ports on the
Router. Check that the LAN Port Status LED lights.
Connecting to a Hub or Switch
To share your Router with more than four users you will need an additional
Hub or Switch. Connect a LAN port of your Router to the hub or switch.
Your existing
Cable/DSL
Internet
Modem
OfficeConnect
Secure Router
OfficeConnect
Switch
Figure 1 Example Network with OfficeConnect Secure Router.
4
CONFIGURING YOUR ROUTER
Keeping Your Existing IP Configuration
If you don't want to change your IP infrastructure or have static IP addresses
the Discovery Application, found on the accompanying CD, can be used to
locate the Router. You can then use the Setup Wizard to set its IP parameters.
Refer to the User Guide for more details.
Running the Setup Wizard
1. If you haven't already done so, restart your computer.
2. Launch your web browser and attempt to contact the Router by typing
the following URL in the location bar: http://192.168.1.1, If you are
able to access the Login page, then your computer has correctly
received an IP address from the Router.
3. Login using the default password admin. The Wizard will attempt to
launch automatically, but if it fails, select the Setup Wizard tab and
click on the Wizard... button.
4. Where possible, the wizard will recommend settings for most
parameters. However, there are some settings which you must
provide. Most of these will have been provided to you by your ISP
when you set the account up.
5. By default, 3Com recommends that you leave the LAN IP address for
the Router as 192.168.1.1. However, if you should choose to change
it, make a note of the new address :
Router's LAN IP Address
_______._______._______._______
6. When the DHCP Server Settings page is displayed, make sure that the
Enable the DHCP Server with the following settings option is selected.
3Com recommends that you leave the DHCP Server at the default values,
unless you already have a DHCP Server on your network.
2
CHANGING YOUR COMPUTER'S CONFIGURATION
You may need to make some changes to the configuration of your computers in
order to communicate with the Router.
DSL Users with PPPoE or PPTP Client Software
If you have PPPoE or PPTP client software installed on your
computer, you will need to disable it. To do this:
1. From the Windows Start menu, select Settings >
Control Panel.
2. Double click on Internet Options.
3. Select the Connections Tab. A screen similar to
Figure 2 should be displayed.
4. Select the Never Dial a Connection option and click OK.
You may wish to remove the PPPoE or PPTP client software
from your computer to free resources, as it is not
required for use with the Router.
Obtaining an IP Address automatically
Follow the instructions below for your particular operating system to ensure that
your computers are configured to obtain an IP address automatically.
For computers using Windows 2000 and 2003 Server.
1. From the Windows Start Menu, select Settings > Control Panel.
2. Double click on Network and Dial-Up connections
for Windows 2000 (or Network Connections for
Windows 2003).
3. Double click on Local Area Connection.
4. Click on Properties.
5. A screen similar to Figure 3 should be displayed.
Select Internet Protocol TCP/IP and click on Properties.
6. Ensure that the options Obtain an IP Address
automatically, and Obtain DNS servers automatically
are both selected as shown in Figure 4. Click OK.
7. Restart your computer.
Connecting to the Internet
When the Wizard has completed, attempt to browse to an Internet web site,
such as www.3com.com. If you can successfully access this site, then your
computer, Router and internet modem have been correctly configured.
Now that you have successfully configured your Router 3Com recommends,
as part of our continuous improvement process, you download the latest
firmware from the web at www.3com.com.
Refer to the Problem Solving section if you cannot make contact with the
Router or the Internet.
Connecting Additional Computers
You may now connect additional computers to the remaining 10/100 LAN
ports on the Router. Ensure that each computer you connect to the Router
has been configured as described in section 2. You should restart each
computer whilst it is connected to the Router before you try to use it to
access the Internet.
For computers using Windows 95, 98 and ME.
1. From the Windows Start Menu, select Settings > Control Panel.
2. Double click on Network. Select the TCP/IP item for your network card as
shown in Figure 5 and click on Properties.
3. In the TCP/IP dialog, select the IP Address tab, and ensure that Obtain IP
address automatically is selected as shown in Figure 6. Click OK.
4. Restart your computer.
For computers using Windows XP.
1. From the Windows Start menu, select Control Panel
2. Click on Network and Internet Connections
3. Click on the Network Connections icon
Figure 2
4. Double click on LAN or High Speed Connection icon. A screen titled Local
Area Connection Status will appear
5. Select Internet Protocol TCP/IP and click on Properties.
6. Ensure that the options Obtain an IP Address automatically, and Obtain
DNS servers automatically are both selected as shown in Figure 4. Click OK.
7. Restart your computer.
Figure 3
Figure 4
Figure 5
PROBLEM SOLVING
If you are experiencing difficulties with your installation, try the following:
• Ensure all networking equipment is switched on. The Router
should be showing a green Power LED. If it is not, check the power
adapter connection. Do not use any power adapter with your Router
other than the one supplied.
• Ensure the Cable/DSL Modem is connected. The Router should be
displaying a green or yellow Cable/DSL Status LED. If no LED is
displayed, check that your modem is switched on and that it is
connected to the Cable/DSL port with an Ethernet cable.
• Ensure that the computer is connected to the Router. The Router
should be displaying a green or yellow LAN Status LED. If it is not,
check that the computer is connected to one of the Router's LAN ports
with an Ethernet cable.
• Ensure that the Alert LED has stopped flashing. The Alert LED may
continue to flash for one minute or longer during start up, depending on
your network configuration. Wait until the Router completes its self test
routine, and the Alert LED is off.
• Ensure your computer is configured correctly. Make sure that the
computer obtains an IP address automatically. See Section 2 for details.
Ensure that the NIC card is configured for autonegotiation.
• Ensure that you do not have a web proxy enabled on your
computer. Go to the Control Panel and click on Internet Options.
Select the Connections tab and click on the LAN Settings button at the
bottom. Make sure that the Use Proxy Server option is unchecked.
• You are unable to access the Router's Web interface. Launch a
web browser and enter http://192.168.1.1. If you chose a different IP
address, use that instead. Ensure that you include the http:// prefix.
3
ISP CONNECTION METHODS
Before you can configure the Router you need to know the IP information
allocation method used by your ISP. There are four different ways that ISPs
allocate IP information, as described below:
1. Dynamic IP Address (DSL or Cable)
Dynamic IP addressing (or DHCP) automatically assigns the Router IP
information. This method is popular with Cable providers. This method
is also used if your modem has a built in DHCP server.
2. PPPoE (DSL only)
If the installation instructions that accompany your modem ask you to
install a PPPoE client on your PC then select this option. Note that
when you install the Router, you will not need to use the PPPoE
software on your PC. To configure the Router you will need to know
the following: Username, Password, and Service Name (if required by
your ISP).
3. Static IP Address (DSL or Cable)
The ISP provides the IP addressing information for you to enter
manually. To configure the Router you will need to know the following:
IP Address, Subnet Mask, ISP Gateway Address, and DNS address(es).
4. PPTP (DSL or Cable)
PPTP is used by some providers, mostly in Europe. If the installation
instructions that accompany your modem ask you to setup a dialup
connection using a PPTP VPN tunnel then select this option. Note that
when you install the Router, you will not need to use the dialup VPN
on your PC anymore. To configure the Router you will need to know
the following: Username, Password, and VPN Server address (usually
your modem).
You will be asked for the IP Allocation Mode when you run the Setup Wizard.
Figure 6
• You cannot remember the Router IP address. Run the Router
Discovery application from the CD-ROM. This will always connect you
to the Router.
Cable Internet Connections.
• Some Cable providers authenticate to the user's computer MAC
address. If this is required, go to Network Settings > Connection to ISP
and select Dynamic IP address as the IP allocation mode. Select Clone
the MAC Address. This will copy the MAC address of your computer
onto the Internet port of the Router.
• Some Cable providers authenticate to the user's Host Name. If this is
required, go to Network Settings > Connection to ISP and enter the
host name of your computer into the Host Name field.
DSL Internet Connections.
• If you have an existing DSL line and have PPPoE or PPTP client
software installed on your computer, you will need to disable it. See
section 2.
• If your DSL line is using PPPoE or PPTP, go to Network Settings >
Connection to ISP and ensure that the correct IP allocation mode is
selected. Check that your Username and Password are correct.
• Some DSL providers require the use of a PPPoE Service Name. If this is
required, go to Network Settings > Connection to ISP and enter the
PPPoE Service Name in the field provided. If it is not required, you
must leave it blank.
For further Problem Solving and Technical Support information,
refer to the Router User Guide, supplied in PDF format on the CD-ROM
that accompanies your Router.