Sony BVP-900P Series Manual de instrucciones - Página 8
Navegue en línea o descargue pdf Manual de instrucciones para Videocámara Sony BVP-900P Series. Sony BVP-900P Series 48 páginas. Color video camera
Imprimir páginaLocation and Function of Parts
1 Up tally lamp
Lights when the camera receives a red tally signal.
When the CALL button on the MSU-700 or
RCP-700-series unit is pressed with the CCU CALL
switch on the internal MS board set to ON, the lamp
lights if it is not lit, and goes out if it is lit. You can
adjust the brightness of the lamp with the control on
the internal MS board.
Not to have this lamp light, set the UP TALLY switch
on the rear panel to OFF.
Attach the supplied number plate (0 through 9) to
show the camera number.
For details on adjusting the brightness and attaching the
number plate, refer to the System Manual.
2 Safety lock
Locks the side panel to prevent it from accidentally
opening. To open the side panel, loosen the side-panel
lock screw, slide the safety lock toward the lens, and
open the panel.
When you close the side panel, it automatically locks.
For details, refer to the System Manual.
3 Camera number plate
Attach the supplied light gray number plate to show
the camera number.
For details how to attach a number plate, refer to the
System Manual.
4 Side-panel lock screws
Lock the side panel to prevent it from accidentally
opening. Turn it fully clockwise.
5 Lens lock and knob
Locks the lens. To attach or detach the lens, turn the
knob fully counterclockwise until the lever is
horizontal. To lock the lens, turn the knob clockwise
until the lever is vertical.
6 Cable clamp
Fixes the triax cable. This accepts a cable from 8 to 15
mm in diameter.
For details on how to use the cable clamp, refer to the
System Manual.
7 AUDIO IN CH-1 and CH-2
(audio input channels 1 and 2) connectors (XLR
3-pin)
Accept microphone or line level signals.
6 (E)
8 AUDIO IN (audio input select) selector
Set to the appropriate position according to the
equipment connected to the AUDIO IN CH-1 and
CH-2 connectors.
MIC: When microphones are connected.
LINE: When a line-level signal source is connected.
9 Microphone power switches
For the microphones connected to the AUDIO IN CH-
1 and CH-2 connectors, respectively.
+48 V: When the connected microphone requires an
external power source.
A power of +48 V is supplied to the microphone.
OFF: When the connected microphone requires no
external power.
•
: Not used
!º PROMPTER (teleprompter) connector
(BNC type)
Supplies the signal for the teleprompter monitor, which
is input to the PROMPTER INPUT connector on the
CCU-700A/700AP.
!¡ TEST OUT (test signal output) connector (BNC
type)
Supplies the signal selected with the video signal select
buttons on the rear panel when the TEST OUT switch
on the MS board is set to VF.
When the TEST OUT switch is set to RET, a return
video signal is output. (The return video signal
selected last is output.)
When a BKP-7910/7910P Stand-Alone Kit is installed
in the camera, a composite video signal is output if the
TEST OUT switch is set to VBS.
!™ TRACKER connector (10-pin)
Used for communication between the camera operator
and tracker and for intercom 1 and 2 connection. This
also supplies the up tally and program audio signals.
!£ RET CONTROL (return video control)
connector (6-pin)
Used for switching the return video 1, 2, 3, and 4
signals and for turning the intercom microphone on or
off from the external equipment.
!¢ SCRIPT (script light) connector (4-pin)
Supplies power (12 V, 5 W maximum) for the script
light.