Argo ULISSE ECO Manual de instrucciones - Página 8
Navegue en línea o descargue pdf Manual de instrucciones para Aire acondicionado Argo ULISSE ECO. Argo ULISSE ECO 16 páginas. Room air conditioner with remote condenser
También para Argo ULISSE ECO: Manual de instalación (14 páginas)
Imprimir página
HOW TO SET THE CLOCK
EN
1. Press for a few seconds the Timer button
Press the button
SET
WEEK
F
S
S
M
T
W
T
2. AM or PM starts flashing: use the arrows to choose
AM or PM, then confirm with
The hour indication starts flashing: set the hour with
the arrows, then confirm with
The minutes indication starts flashing: set the
minutes with the arrows, then confirm with
WEEK starts flashing: set the day of the week with
the arrows, then confirm with
3. At this point the procedure is finished: press the
button
to exit the clock menu.
COOLING / AUTOMATIC MODE
1. Turn on the unit with the ON / OFF
button.
2. Press the button
COOLING symbol
the display.
3. Press the buttons
desired temperature (the temperature
range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD "SET".
4. Press the button
NOTES
If the fan is set in automatic mode and the unit stops
because setpoint is reached, also the fan will stop.
If the fan is set in one of the six manual speeds, it will
go on operating at the selected speed, even if the unit
stops due to reaching the setpoint.
•
When the external or internal temperature is too low,
the unit could limit the speed of the compressor or
switch it off for a certain period of time to avoid the
formation of ice on the internal heat exchanger.
.
ARROWS
WEEK
T
S
M
AUTO
SET
WEEK
until the
S
M
T
W
appears on
2
to set the
1
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
to select the fan speed.
DEHUMIDIFYING MODE (DRY)
.
1. Turn on the unit with the ON / OFF button
2. Press the button
appears on the display
3. Press the buttons
(the temperature range is between 10 °C and 32 °C).
SET
THE DISPLAY SHOWS THE
W
T
F
S
SELECTED TEMPERATURE
AND THE WORD "SET".
NOTES
• Use DRY operation when you want to reduce the
humidity in the room.
• Once the room temperature reaches the set level, the
unit repeats the cycle of turning on / off automatically.
• During DRY operation, the fan speed is automatically
set (Remote control lamp
dehumidification.
• Dry operation is not possible if the indoor temperature
is less than 10 °C.
FAN ONLY MODE
T
F
S
If you want to make air circulate without any temperature
3
control, press the button
4
appears on the display
ADJUSTING THE FAN SPEED
AUTOMATIC
Set with the button
AUTO
. The unit automatically controls the fan speed.
When the air conditioner starts operating, the fan speed
varies according to the thermal load of the room .
NOTE
In FAN ONLY mode, the AUTOMATIC speed corresponds
to the high speed H.
MANUALE
If you want to manually adjust the fan speed just set the
button
as desired:
AUTO
VH
L
Low
ML
Medium-low
M
Medium
8
until the DEHUMIDIFYING symbol
.
to set the desired temperature
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
S E T T I N G T H E D I S P L A Y
W I L L S H O W T H E R O O M
TEMPERATURE AGAIN.
AUTO
is ON) to maximize
until the FAN symbol
.
the "AUTO" position
L
ML
H
MH
MH
Medium-high
H
High
VH
Very high
M